Omega DP25B-RTD, Quick Start Manual

Page: 2 / 2

To Set the RTD Type:
1. Press MENU until the meter
displays:
2. Press /DEV . The meter
displays:
3. Press /MAX until the RTD for
your installation is shown.
• RTD.2 is for a 2-wire RTD
• RTD.3 is for a 3-wire RTD
• RTD.4 is for a 4-wire RTD
4. Press MENU to select the RTD shown. The meter
displays:
To Set the Decimal Point Position:
1. If it's not already shown, press
MENU until the meter shows:
2. Press /DEV. The meter
displays:
3. Press /MAX to move the decimal point to the
desired location.
Choices are: FFFF or FFF.F
4. Press MENU to select the decimal point position
shown. The meter displays:
5 6
To Select the Temperature Unit
(Fahrenheit or Celsius):
1. If it's not already shown, press
MENU until the meter shows:
2. Press /DEV. The meter
displays:
3. Press /MAX to display the
setting you want. Choices are
F and C .
4. Press MENU to select the temperature meter
shown. The meter displays:
Begin Operation
Reinitialize the meter (press
RESET twice or press MENU
until RST flashes on the display).
When the temperature appears,
the meter is up and running.
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET /MAX
SETPTS /DEV MENU RESET
/MAX
SETPTS /DEV MENU RESET
/MAX
SETPTS /DEV MENU RESET /MAX
DP25B-RTD and DP25-RTD
Programmable Digital
RTD Meter
MQS3733/0206
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for a period of
one (1) year from the date of
purchase. In addition to OMEGA’s standard warranty period, OMEGA
Engineering will extend the warranty period for
four (4) additional years if the
warranty card enclosed with each instrument is returned to OMEGA.
If the unit should malfunction, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective it will be repaired or replaced at no
charge. Omega's WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of being damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental
or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in
or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY
/ DISCLAIMER language, and additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising
out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the
return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please
have the following information available
BEFORE contacting OMEGA:
1. P.O. number under which the
product was PURCHASED,
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following information
available BEFORE contacting OMEGA:
1. P.O. number to cover the COST of
the repair,
2. Model and serial number of product,
and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2006 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of OMEGA ENGINEERING, INC.
PATENT NOTICE: This product is covered by one or more of the following
patents: U.S. Pat. No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599;
2052600 / ITALY 1249456; 1250938 / FRANCE BREVET No. 91 12756 / SPAIN
2039150; 2048066 / UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY
DE 41 34398 C2. The “Meter Case Bezel Design” is a trademark of NEWPORT
Electronics, Inc. USED UNDER LICENSE. Other U.S. and International patents
pending or applied for.
Servicing North America:
USA: NN One Omega Drive, P.O. Box 4047
ISO 9001 Certified
N Stamford CT 06907-0047
NN TEL: (203) 359-1660NN FAX: (203) 359-7700
NN e-mail: info@omega.com
Canada:> N 976 Bergar
NN Laval (Quebec) H7L 5A1
NN TEL: (514) 856-6928NN FAX: (514) 856-6886
NN e-mail: info@omega.ca
For immediate technical or application assistance:
USA and Canada: N Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA ®
NN Customer Service: 1-800-622-2378 / 1-800-622-BEST ®
NN Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN ®
Mexico and N TEL: (001)800-TC-OMEGA
®
N FAX: (001) 203-359-7807
Latin American: N En Español: (001) 203-359-7803N
NN e-mail: espanol@omega.com
Servicing Europe:
Czech Republic: N Frystatska 184, 733 01 Karviná
NN TEL: +420 59 6311899NN FAX: +420 59 6311114
NN e-mail: info@omegashop.cz
Germany/Austria: N Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
NN TEL: +49 7056 9398-0NN FAX: +49 7056 9398-29
NN Toll Free in Germany: 0800 639 7678
NN e-mail: info@omega.de
United Kingdom: N One Omega Drive
ISO 9002 Certified N River Bend Technology Centre
NN Northbank, Irlam Manchester M44 5BD United Kingdom
NN TEL: +44 161 777 6611N FAX: +44 161 777 6622
NN Toll Free in England: 0800 488 488
NN e-mail: sales@omega.co.uk
OMEGAnet ® On-Line Service
www.omega.com
Internet e-mail
info@omega.com
®
®
USA
MADE IN
This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.
TRADEMARK NOTICE:
®
omega.com
®
, and ,
are trademarks of OMEGA
®
WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.
Engineering, Inc.