OMCN 388/B Instructions For Use, Maintenance And Spare Parts Download Page 2

L388BS002 

GENERAL SAFETY RULES:

 

OMCN S.p.A. cannot be held responsible for direct or indirect injury or damage to persons, animals or things caused by the 

failure to observe the instructions contained in this handbook. 

 

any  tampering  or  modifications  to  the  equipment  automatically  and  immediately  nullifies  the  guarantee  and  relieves  the 

manufacturer of any liability for direct or indirect injury caused by such tampering or modifications.  

 

The machine may only be used

 by responsible staff in good health who have been specially trained to use the equipment and are 

acquainted with all the risks. 

 

The machine, can only be used 

by one operator at a time. 

 

It is mandatory 

to wear adapted clothes to use this mechanical lifting equipment as required by the rules into force in the country it 

is used in. 

 

 

 

 

 

 

 

 

 

The  wheels  must  be  entirely  put  inside  and  supported  by 

the equipment. 

 

 

 

 

 

 

 

 

 

 

 

 

Put the mechanical lifting equipment under the wheel using the dedicated handle (1). 

 

 

 

 

 

 

 

 

 

 



It is mandatory

 to check that the equipment fits the wheel’s dimensions. 

 

 



It is mandatory to check that the floor where the equipment moves is free of objects, clean, flat, and able to support the load of the 

equipment and the element loaded on the equipment. The supporting surface where the user intends to operate must be free of 

slits, holes or manhole covers where the wheels could jam or get stuck.  

 

 



Before starting to operate the equipment, 

make sure 

that it is complete of all its parts and in perfect working order. Otherwise, 

using the equipment is 

prohibited

.

 

 

 



Before  operating  with  the  equipment,

  it  is  compulsory 

to  check  that  the  operating  area  is  sufficiently  illuminated  (sufficiently 

illuminated area but not subject to glare or intense light). 

 



It is mandatory

 to make sure that the wheel is secured to the equipment by the wheel securing device before moving the wheel. 

 

 



Before operating with the equipment, 

it is compulsory

 to make sure there are no objects, materials or pieces that may hinder the 

movement  of  the  wheels  of  the  hydraulic  equipment.  No  traces  of  oil  or  other  liquids  must  be  present  that  may  make  the  floor 

slippery.  

IT IS COMPULSORY: 

OK 

www.omcn.it

Summary of Contents for 388/B









Reviews: