manualshive.com logo in svg

OMAC B Series, Installation, Operation And Maintenance Manual

Share
Download
OMAC B Series Installation, Operation And Maintenance Manual Download Page 19

19

7. Untighten the socket head screws on mechanical

seal.

8. Extract the rotating part of the mechanical seal from

the shaft.

9. IMPORTANT!
   

 

During the following operations, take care you don't

damage the lapped seal surface; don't lay them on
the bench and handle them with clean hands.

10. Clean carefully the shafts.

Lubricate lightly the O-ring and introduce the rotating

part of the seal, possibly by means of a conical
bush.

Exert pressure only with hands; avoid using metal

tools.

11. Be sure the mechanical seals stand on the shaft

shoulder and tighten by degrees the socket head
screws. We suggest you should use a thread locking
adhesive in order to avoid their untightening on
work.

12. Assemble the stationary part of the seal on rotor

case, taking care to aline the slot with the retainer
pin, already arranged on seat bottom.

ROTOR CASE ASSEMBLY Mod. B1 - B2 - B3 - B4 - B550

Summary of Contents for B Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands