Olympus PT-022 Instruction Manual Download | Manualshive

Page: 25 / 43

background image

E-24

Perform the final checks.

Visual Inspection

After sealing the Case, check the sealing part of front and rear lid
visually to confirm that the O-ring is not twisted or out of the groove
and that no foreign matter has been caught.

Fit the lens cap onto the lens
ring as shown in the figure. Be
sure to remove the lens cap
before shooting.

Mounting and Removing the Lens Cap

:

• After loading the camera into the Case, confirm that the

mode dial moves. If it does not move, there is the
possibility that oil or fat has been attached to the mode
dial. Please wipe it clean.

CAUTION

Try to move the mode dial.

After sealing, turn the mode dial knob and confirm that the mode
dial of the camera is switched.

Set the power to 'ON'.

Move the power switch and confirm that the camera power can be
switched ON and OFF.

:

• Hairs, fibers, and other narrow items are not very apparent,

but they may cause entry of water, so that special attention
is required.

CAUTION

PT̲022̲E.qxd 2004.3.18 4:34 PM ページE-24

«
...
23
24
25
26
27
...
»

Summary of Contents for PT-022












































Reviews:

No comments

Related manuals for PT-022

Brand: Waycon Pages: 8

Brand: Calumet Pages: 4

scx-4100 series

Brand: Samsung Pages: 8

Event Master E2

Brand: Barco Pages: 2

Brand: Barco Pages: 7

Brand: Barco Pages: 7

Brand: Tailfin Pages: 8

Brand: DANA Pages: 42

Brand: Yakima Pages: 8

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

Brand: Monacor Pages: 2

Brand: JASTEC Pages: 12

Brand: parktool Pages: 2

Brand: Pivot Pages: 4

Brand: GOgroove Pages: 9

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: Yakima Pages: 8

Brand: Hama Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands