background image

19

PROPER SELECTION OF THE POWER SUPPLY CORD

If no power supply cord is provided, please select the proper power supply cord for the equipment by referring to “Specifications" 
and "Certified Cord" below.

CAUTION : In case you use a non-approved power supply cord for Olympus products, Olympus can no longer warrant 

the electrical safety of the equipment.

Country

Agency

Certification Mark

Argentina

Australia

Austria

Belgium

Canada

Denmark

Finland

France

Germany

Ireland

IRAM

SAA

ÖVE

CEBEC

CSA

DEMKO

FEI

UTE

VDE

NSAI

Country

Agency

Certification Mark

Italy

Japan

Netherlands

Norway

Spain

Sweden

Switzerland

United Kingdom

U.S.A.

IMQ

 

KEMA

NEMKO

AEE

SEMKO

SEV

ASTA, BSI

UL

A power supply cord should be certified by one of the agencies listed in Table 1, or comprised of cordage marked with an 
agency marking per Table 1 or marked per Table 2. The fittings are to be marked with at least one of agencies listed in Table 1. 
In case you are unable to buy locally in your country the power supply cord which is approved by one of the agencies 
mentioned in Table 1, please use replacements apprpved by any othere quivalent and authorized agencies in your country.

Voltage Rating
Current Rating
Temperature Rating
Length
Fittings Configuration

125V AC  (for 100-120V AC area) or, 250V AC  (for 220-240V AC area)
6A minimum
60 minimum
3.05 m maximum
Grounding type attachment pulg cap Opposite teminates in molded-on IEC con-
figuration appliance coupling.

Specifications

Table 1 Certified Cord

JET, JQA , TÜV,
UL-APEX / MITI

Summary of Contents for CX31

























Reviews: