background image

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-5RE Modular Revolving Nosepiece                

   

 

Page 3 of 18 

 

 

Revision 3 

Sources for Replacement Parts, Tools, and Supplies Referenced in this Document ........................................................ 18 

 

Table of Figures 

Figure 1 

 A typical JIS Screw .................................................................................................................................................. 5 

Figure 2 

 The BH2-5RE modular revolving nosepiece ........................................................................................................... 6 

Figure 3 

 Basic components of the BH2-5RE ......................................................................................................................... 6 

Figure 4 

 Remove four screws securing the dovetail slide .................................................................................................... 7 

Figure 5 

 Remove the loose dovetail slide ............................................................................................................................ 7 

Figure 6 

 Remove screws securing the cover in place .......................................................................................................... 7 

Figure 7 

 Remove the protective cover ................................................................................................................................. 7 

Figure 8 

 The turret assembly (without cover) ..................................................................................................................... 7 

Figure 9 

 Screwdriver modified to remove slotted lock ring ................................................................................................ 8 

Figure 10 

 Insert screwdriver into bores to lock turret ......................................................................................................... 8 

Figure 11 

 Loosen the slotted lock ring ................................................................................................................................. 8 

Figure 12 

 Remove the slotted lock ring ............................................................................................................................... 8 

Figure 13 

 Remove the pivot-adjustment screw ................................................................................................................... 9 

Figure 14 

 Remove the center-pivot bearing ball ................................................................................................................. 9 

Figure 15 

 Remove the screws securing the detent stop ...................................................................................................... 9 

Figure 16 

 Remove the loose mechanical detent stop .......................................................................................................... 9 

Figure 17 

 Remove the knurled-rubber grip ring .................................................................................................................. 9 

Figure 18 

 Components of the turret assembly .................................................................................................................. 10 

Figure 19 

 Loosen the threaded retaining ring ................................................................................................................... 10 

Figure 20 

 Remove the threaded retaining ring .................................................................................................................. 10 

Figure 21 

 Remove the perimeter bearing balls ................................................................................................................. 10 

Figure 22 

 Lift and remove the stationary base .................................................................................................................. 10 

Figure 23 

 Reinstall stationary base into revolving turret ................................................................................................... 11 

Figure 24 

 Apply ring of fresh grease for the bearing balls ................................................................................................. 11 

Figure 25 

 Place the bearing balls into the ring of grease ................................................................................................... 11 

Figure 26 

 Engage the threaded retaining ring ................................................................................................................... 11 

Figure 27 

 Tighten the threaded retaining ring ................................................................................................................... 11 

Figure 28 

 Remove any grease squeeze-out ....................................................................................................................... 12 

Figure 29 

 Apply grease to the center-pivot bore ............................................................................................................... 12 

Figure 30 

 Place bearing ball into the center-pivot bore .................................................................................................... 12 

Figure 31 

 Apply grease to the top of the bearing ball ....................................................................................................... 12 

Figure 32 

 Reinstall the pivot-adjustment screw ................................................................................................................ 12 

Figure 33 

 Reinstall the slotted lock ring ............................................................................................................................. 13 

Figure 34 

 Tighten the slotted lock ring .............................................................................................................................. 13 

Figure 35 

 Place the mechanical detent stop in position .................................................................................................... 13 

Figure 36 

 Secure the detent stop with two screws ........................................................................................................... 13 

Figure 37 

 Apply grease to the five detent notches ............................................................................................................ 14 

Figure 38 

 Place cover in position on the turret assembly .................................................................................................. 14 

Figure 39 

 Secure protective cover using three screws ...................................................................................................... 14 

Figure 40 

 Position dovetail slide onto stationary base ...................................................................................................... 14 

Figure 41 

 Secure dovetail slide onto stationary base ........................................................................................................ 14 

Figure 42 

 Apply black adhesive to revolving turret ........................................................................................................... 15 

Figure 43 

 Reinstall the knurled-rubber grip ring ................................................................................................................ 15 

Figure 44 

 Remove any adhesive squeeze-out .................................................................................................................... 15 

Summary of Contents for BH2-5RE



















Reviews: