SELF-TESTING MAINTAINED EMERGENCY ILLUMINATION SIGNS WITH WHITE LEDs
ZLD-34
ZLD-44
ZLD-28
TECHNICAL CHARACTERISTICS
Operation temperature range
Relative humidity
Construction materials
External dimensions
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Batteries (Ni-MH)
Recharging time
Battery protection
Indications
Minimum emergency duration
Degrees of cover protection
Produced in accordance with
Light source intensity (230V) / (emerg.)
220-240V AC/50-60Hz
3h
24h
Overcharging and full discharging protection
Charge LED, Lamp Fault LED, Fault LED
IP 40
3.6V/1.5Ah
125lm / 125lm
170lm / 125lm
145lm / 125lm
4.3W / 6.9VA
4W / 6.7VA
3.8W / 6.5VA
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
, EN 1838
0 40 C
o
to
up to 95%
Aluminum
,
plexiglas
290x152x38mm
3 years
(1
year for the battery
)
350x222x38mm
450x275x38mm
922504450_09_018
Page
1 from
4
Thank you for purchasing this product of Olympia
operation test is initiated. During this test period
Electronics. A European manufacturer.
all indication LEDs are OFF.
GENERAL
Automatic test
o
This test includes all the operations that provide
These luminaires are used indoors
(
ta 40 C
)
the manual test and is conducted automatically
where emergency light is needed.
every 15 days. In order to be performed, the
Each luminaire must be permanently connected
main power supply and the battery should be
to mains power supply
.
connected.
In normal operation the led strip lights and the
Automatic Autonomous Test
battery is charging.
The Automatic Autonomous Test is conducted
In case of a mains power supply failure the
and measures the luminaire`s back up
luminaire will light the led strip automatically in
operation. This test is conducted automatically
emergency mode (powered by its battery). When
every six months
.
In order to be performed, the
the mains power supply is restored the device
main power supply and the battery should be
turns to normal operation.
connected (the battery should be charged)
.
If
Installation
the battery is not charged
,
the test is postponed
To install the illumination sign you must follow
until the battery is completely charged. If during
the installation instructions on pages 2 and 3.
the Automatic Autonomous Test the luminaire’s
Battery Cut-off
duration is lower than the named, then the
The luminaire enters in this operation when the
battery must be replaced.
mains power supply fails
and battery has lost its
Back Up Operation
energy
.
During this operation the luminaire
The autonomous duration of battery during
enters the idle state
and battery consumption is
emergency mode is at least the one that is
negligible, in order to be protected from deep
stated in the list of the first page. During
discharge.
emergency mode, a LED strip test is also
Battery charging
performed.
The battery charging is completely controled
.
In
Resetting Errors
this case, is
achieved the perfect battery
Push the Test button for 5 seconds, to
maintenance
,
as well as the elongation of its
extinguish all the indicated LED errors. Then
duration
.
When the
the luminaire enters regular
operation mode.
battery has completely charged
,
it charges with
Changing the operating mode
a maintenance current.
Press and hold the TEST button for more than 5
Manual
Test
seconds
,
the l
uminaire
will erase first the errors (3
The manual test can be conducted only if the
LED indicators will light in succession) and
after
2
main power supply and the battery is
seconds the LED Lamp Fault will remain lit
connected.By pressing the test button briefly an
High Quality European based Manufacturers
700gr.
1060gr.
1570gr.
