background image

921489000_09_005

Page. 1 from 4

BS-489

                       Auto Dialer

TECHNICAL SPECIFICATION

Thank  you  for  purchasing  this  product  of 
O l y m p i a   E l e c t r o n i c s .   A  E u r o p e a n  
manufacturer.

GENERAL

Auto  dialer  BS-489  is  a  device  that 
transmits  the  stored  messages  over  the 
phone line when it is properly triggered.

  On  the  front  panel  there  is  a  user-
frienly  control  panel  with  4  keys  and  a 
display.

  It  is  combined  with  all  alarm  panels 
( e g  B S - 4 1 7 ,  B S - 4 1 8 )  a n d  w i t h  f i r e 
alarm  panels  (eg  BS-632,BS-634,BS-
6 3 6 , B S - 11 6 ) 

m a d e 

b y 

O l y m p i a 

Electronics.  It  is  also  compatible  with 
similar  products  on  the  market.  It  can 
be used with two different panels at the 
same  time,  and  transmits  two  different 
messages, one for each panel. It has a 
m e m o r y  f o r  t e n  p h o n e  n u m b e r s  o f 
twenty  digits  each  and  it  is  locked  with 
a four digit access code.

  The  device  has  a  built-in  microphone 
f o r    r e c o r d i n g  m e s s a g e s ,  a n d  a n 
earphone  is  included  in  the  package, 
for listening the messages.

  A l l  p h o n e  n u m b e r s ,  s e t t i n g s ,  a n d   
messages  are  recorded  in  the  memory 
and  are  not  lost  in  case  of  a  power 
failure, and can be changed by the user 
when needed.

  I t  i s  u s e d  t o  i m m e d i a t e l y  c a l l  t h e 
police, the fire department, the owners 
etc, in case of emergency

  When  triggered,  the  auto-dialer  dials 
t h e  p h o n e  n u m b e r s  s t o r e d  i n  i t s 
memory,  in  priority  (0-9)  as  stored  by 
the  user.  The  device  skips  the  blank 
memory positions.

 

MOUNTING

  The bottom cover can be removed by 
unscrewing  the  retaining  screw  at  the 
bottom  side  of  the  device.  For  wall 
mounting  the  mounting  holes  on  the 
two  corners  of  the  device  (shown  on 
figure  1)  can  be  used. The  appropriate 
mounting screws for wall mounting, are 
included.

CONNECTIONS

 

At the bottom right side of the 

device there are the terminal blocks 

Operating Voltage

Degrees of cover protection

User interface

Consumption
Inputs
Outputs

Produced in accordance with
Operation temperature range
Humidity
Constructional materials
Dimensions ( L x W x H ) 
Weight
Guarantee

10 - 30 V DC

Idle 10mA (24V) or 25mA (12V). Active 25mA (24V) or 70mA (12V)

2 alarm inputs and 2 messages, built-in microphone and earphone

160 gr.

105 x 65 x 28 mm 

Polycarbonate

Up to 95% Relative Humidity

ï

0 to 60  C 

TBR-21, EN61000-3-2, EN 61000-3-3 

IP 20 

1 Display and 4 programming keys

tone or pulse call and transmission of messages through phone line 

2 years

High Quality European based Manufacturers

Summary of Contents for BS-489

Page 1: ...ed by the user when needed It is used to immediately call the police the fire department the owners etc in case of emergency When triggered the auto dialer dials the phone numbers stored in its memory in priority 0 9 as stored by the user The device skips the blank memory positions MOUNTING The bottom cover can be removed by unscrewing the retaining screw at the bottom side of the device For wall ...

Page 2: ... rest of the telephone sets are connected When the dialer is idle then these telephone sets are operating normally In case of an alarm the telephone sets are disabled and the dialer takes control of the telephone line OPERATION PROGRAMMING When powered the device is in idle state and this is indicated with a blinking dash In order to set up the device we have to enter the valid access code Enterin...

Page 3: ... as which stands for pause 0 8 seconds that stands for asterisk and that stands for sharp If we want to delete an existing phone number we select its priority and we replace the first digit with and press Displaying saved phone numbers We can check which number is saved in each memory position We select from the menu and press With keys we select the number s priority and we accept with Then the d...

Page 4: ...guously dialling all the stored numbers If we select and then the device is dialling the stored numbers for one time only even when the alarm condition continues The factory default setting for dialler is set to Re Dial Setting We can set how many times every number will be dialled This can be done by selecting and and then with from to and The factory default setting is Message re play setting We...

Reviews: