Vareo MO W+R
Mounting instructions for electricans
11.
Electrical connection:
Caution:
•
Unit with direct connection: shorten the connection
cable and connect it to the floor outlet with less
cable excess.
•
The wash unit with power supply cable must not be
connected to the power supply using an extension
cable.
•
Arrange the power supply cable so that the plug is
easily accessible and can be isolated from the wall
socket.
•
In case several wash units are to be installed in-line,
the power supply cable must not be connected via
further units.
•
The safety regulations of the hairdressing trade
must be observed. Installation and operation
must be in accordance with the norm DIN VDE
0100.
•
During assembly work the complete system
must be isolated from the power supply and
secured against unintended switch-on!
•
In the wash unit, use only the plug-in connectors
supplied with the appliance and specified in the
mounting instructions!
•
Cables must be so arranged that they are not in the
vicinity or moving parts! Damage or crushing must
thus be prevented!
•
The power supply cable from the unit must be
arranged so that it is not jammed between the
unit frame and the floor!
•
The mains cable must be led outward completely and
provided with strain relief.
•
For reasons of mechanical security as well as the
electromagnetic compatibility no cable excess may be
stowed away in the shampoo unit.
Variants for single units:
11.1 Direct connected variant: (
Fig. 6
)
Caution:
This type of connection must only be
made by a qualified electrician!
Connect power supply cable from the floor to
the supplied system socket
(Fig. 4).
Plug system plug into the system socket and close
locking clip
(Fig. 5)
.
Mounting instructions for appliance fitters
11.2 Mains cable variant: (
Fig. 7
)
Route the cable with mains plug through the 140 mm
dia. cutout to the outside.
Shorten the installation tunnel if necessary. The ends of
the tunnel and the cable outlet must be protected with
a PVC strip. Mount lower part of tunnel.
Attach 6 self-adhesive cable clips to the upper section
of the tunnel (the clips must be spaced equally along
the length of the tunnel section). Clip in the connecting
cable.
Caution:
Make sure that the cable outlet on the upper part of
tunnel is on the wall side.
Clip in the upper part of tunnel.
Insert the plug into the wall socket.
In-line installation variants:
11.3
Primary in-line unit with permanent connection
+ secondary in-line unit: (
Fig. 8
)
> Installation of primary in-line unit – see 11.1
> Installation of secondary in-line unit:
Route the distribution cable from the primary in-line
unit through the installation tunnel and connect to the
secondary in-line unit: To do so, detach the control box
from the substructure (Velcro fastening), insert the
system socket of the distribution cable into the control
box and secure with the screw. Reattach the control
box to the substructure.
11.4
Primary in-line unit with mains cable + secondary in-line
unit: (
Fig. 9
)
> Installation of primary in-line unit – see 11.2
> Installation of secondary in-line unit – see 11.3
12. Assembly:
Attach the seat body (2) to the frame and secure the
seat and frame using the 2 hexagon socket bolts (4).
Tighten the 4 wing screws (3) underneath the seat.
Secure the cover sections (7) to the frame (9) using
Velcro tape.
Loosely bind the 2 pressure hoses (hot + cold) and
drain hose together using cable ties.
Caution:
The 3 hoses must not touch the frame (9) at
any point.
Secure the rear cover section (8) to the frame (9) using
the 6 stainless-steel screws. On the vibro-massage
model, reconnect the cables to the adapter cables of
the control box.
Attach the element connecting the seat to the leg rest
(6) and fit the backrest cushion (1).
GB
