background image

Plywood Floor

Large Floor 
Joist Frame

Floor Joists (2)

Floor Runners 
Short (2)

Small Floor 
Joist Frame

Exploded Floor Section

A. Floor Section

Exploded view of all parts necessary to  
complete Floor Section. Identify all parts 
prior to starting.  Note: Floor Footprint is  
96” wide x 45 1/2” deep.

Foundation Material 
not included.

1. 

 Lay out 

Large Floor Joist Frame 

and

 2 Floor Joists 

(1 1/2” x 3 1/2” x 71 7/8”) as illustrated 

above. Position Joists equally in Floor Joist Frame. Use 

Small Floor Joist Frame

 as a template to 

determine joist position. Position Joist so flush with framing. 

Flush 
with 
framing.

Front of GardenSaver

Door Location.

Small Floor 
Joist Frame.

You can find the 
Square Drive Bit, for 
the screws, in the 
Hardware Kit Bag.

2. 

When correctly positioned, attach each Joist with 

4 - 2 1/2” Screws (2 per end)

. You can find 

the Square Drive Bit for the screws in with the Hardware Kit Bag.

Floor Runners 
Long (3)

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 7

Summary of Contents for SS84-SLIDER-METAL-AK





































Reviews: