background image

65.

 Place and align front and side facia for best possible fit with front capping side facia.  Attach facia 

to rafter ends with 

6 - 1 1/2” Finishing Nails

 per piece.  Complete both front facia pieces. 

Rafter/Facia Nailing Strip

Side Angle  
Cut Facia

64.

 Do a dry run first before securing. Position Front Facia up underneath roof panel and against 

rafter ends. Have your helper hold in position. Place angle cut Side Facia underneath roof panel 
against Rafter/Facia Nailing Strip.  Align so Front Facia caps Side Facia and then attach the front 
with 

6 - 1 1/2” Finishing Nails

.  Attach side with 

5 - 1 1/2” Finishing Nails

 securing them into the 

nailing strip (closer to the top of the side facia board).  Attach next piece of Front Facia.  

Note:

  With 

Front Facia correctly aligned at corners, a small gap may occur at center seam. This will be covered 
by Facia Detail Plate in 

Step 65.

Small gap 
may occur.

63.

 Locate and identify all Facia pieces: 

Front & Rear Facia 

(4 @ 1/2” x 4” x 50 1/2”).    

Side Angle Cut Facia 

(2 @ 1/2” x 4” x 54 1/8”). In front corner,

 

align side and front Facia together

Front facia will cap side facia

.  

 

Front 
Facia

Front/Rear 
caps side facia.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 33

Summary of Contents for SS84-SLIDER-METAL-AK





































Reviews: