OLT Maximizer Assembly Manual Download

Page: 2 / 31

Thank you for purchasing a 6x6 Maximizer Storage Shed
Please take the time to identify all the parts prior to assembly.

1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 2

Parts List:

1. Floor Section

2 - 35” x 75” - Floor Frames -

4 - 1 1/2” x 3 1/2” x 72” - Floor Joists -

3 - 1 1/2” x 3 1/2” x 70” Floor Runners -

2 - 5/8” x 34 7/8” x 74 7/8” - Plywood Floor -

2. Wall Section

6 - 35” x 75” - Wall Panels - (Walls with Bottom Plates Unattached) -

6 - 1 1/2”x 2 1/2” x 35” - Bottom Wall Plates -

Door Jambs & Header

2 - 2 1/2” x 3 7/8” x 73” - Vertical Door Jamb with Cleat attached -

1 - 2” x 2 1/2” x 71 3/4” - Door Header -

Top Wall Plates

2 - 3/4” x 2 1/2” x 75” - Side Top Plates (Angle cut on ends) -

2 - 3/4” x 2 1/4” x 65” - Front & Rear Top Plates ( Angle cut on 1 edge) -

2 -

1 1/2” x 5 1/2” x 5 1/2” Front Triangular Corner Brackets -

Gable Walls

2 - Gable Walls - Triangular Shaped -

Misc. Wall

1 pc - Spare Wall Siding -

3. Rafter and Roof Section

12 - 1 1/2” x 3 1/2” x 45” - Roof Rafters with angled ends -

2 - 3/4” x 4 1/2” x 70” - Roof Ridge Boards -

2 - 1/2” x 4 1/2” x 70” - Soffits -

1 - 3/4” x 3 1/2” x 48” - Roof Gusset -

2 - Left Roof Panels 41” (Shingles overhanging plywood on left side) -

2 - Right Roof Panels 41” (Shingles overhanging plywood on right side) -

4 -

Roof/Facia Cleats - 3/4” x 1 1/2” x 42” -

6 - Long Roof Filler Shingles -

2 - Short Roof Filler Shingles -

12 - Roof Ridge Caps -

4. Miscellaneous Trim Section

2 -

3/4”

x 4 3/8” x 79” - Door Trim -

1 -

3/4”

x 4 1/2” x 64” - Front Bottom Skirting -

6 - 1/2” x 4 1/2” x 34 3/4” - Side and Rear Bottom Skirting -

2 - 7/8” x 2 1/2” x 75” - Rear Filler Trim -

2 - 1/2” x 4 1/2” x 77 1/2” - Side Rear Wide Trim -

3 - 1/2” x 2 1/2” x 79” - Narrow Trim (Rear Wall) -

2 - 1/2” x 4 1/2” x 77 1/2” - Side Front Wide Trim -

4 - 1/2” x 4 1/2” x 37 7/8” - Horizontal Gable Trim -

2 - 1/2”x 2 1/2” x 77 1/2” - Narrow Trim (Side Walls) -

2 - Horizontal Gable Detail Plates -

4 - 3/4” x 3 1/2” x 46” - Side Facia - Angle cut both ends - ( 2 right / 2 left) -

2 - 3/4” x 3 1/2” x 79 1/2” - Front and Rear Facia -

2- Pentagon Facia Plate -

1 - Left Side Door -

1 - Right Side Door -

2 - Cedar Shingles used for Shims -

1 - 1/2” x 1 1/4” x 64” - Above Door Trim -

1 - 1 1/2” x 2 1/2” x 64” - Horizontal Door Stop with Dado cut -

1 - 3/4” x 2 1/2” x 62 1/2” - Door Threshold -

1 - 1/2” x 2 1/2” x 71” - Interior Door Flange -

2 - 1/2” x 2 1/2” x 71” - Interior Door Stops -

* Note - Trim pieces are graded best face on the rough side. Use this side out.

Summary of Contents for Maximizer
































Search results

Summary of Contents for Maximizer

Reviews:

Related manuals for Maximizer

Brands by name

Popular brands

OLT Maximizer, Assembly Manual

Search results

Summary of Contents for Maximizer

Reviews:

Related manuals for Maximizer

Brands by name

Popular brands