background image

Note: 

 Our Sheds are shipped 

as unfinished products.  If 
exposed to the elements, the 
Western Red Cedar lumber 
will weather to a silvery-gray 
color. 
If you prefer to keep the cedar 
lumber looking closer to the 
original color, we suggest that 
you treat the wood with a good 
wood stain.  You may also 
wish to paint your new shed 
rather than stain it.  In both 
cases we recommend that you 
consult with a paint and stain 
dealer in your area for their  
recommendations.

We  value  your  feedback  and 
would like to hear back from you 
on how well we are doing in the 
following areas: 
 

1. Customer Service 
2. On Time Shipping 
3. Motor Freight Delivery 
4. Quality of Materials 
5. Assembly Manual 
6. Overall Satisfaction.

The materials contained in this 
Assembly Manual may be downloaded 
or copied provided that ALL copies 
retain the copyright and any other  
proprietary notices contained on the 
materials. No material may be  
modified, edited or taken out of context 
such that its use creates a false or  
misleading statement or impression as 
to the positions, statements or actions.

Canadian Address 
9393 287th Street 
Maple Ridge, British Columbia 
Canada     V2W 1L1

United States Address 
P.O. Box 96 
Sumas, Washington 
USA    98295

Outdoor Living Today

Please call, write or email us at: 

Toll Line: 1.888.658.1658         |      Fax: 1.604.462.5333      |      [email protected]

Congratulations on completing 
your 8x4 GardenSaver Shed!

Page 36

Summary of Contents for GS84-SLIDER-CEDAR-FJ





































Reviews: