OLT Garden Chalet Assembly Manual Download Page 15 | Manualshive

Page: 15 / 19

OLT Garden Chalet Assembly Manual Download Page 15

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 15

29.

Place

Side / Front Corner Trims (4E) - 1/2”x 2 1/2” x 61”

(angle cut one end) tight against front

corner door trim and up underneath side facia trim. The bottom of the trim should be flush to the bottom
of the floor. Secure with

6 - 1 1/2” Finishing Nails (K).

Once again there are left/right side corner trims.

Confirm before attaching. Complete both sides.

30.

Locate

Side / Rear Corner Trims (4F)

- 1/2”x 3 1/2” x 65 1/2”

(angle cut one end). Position in rear

corner as illustrated above. The side / rear trim will cap the rear trim

(4I)

found in

Step 33

. Do a dry run to

confirm location before attaching. The bottom of the trim should be flush to the bottom of the floor. When
correctly aligned, secure each piece with

8 - 1 1/2” Finishing Nails (K).

Once again there are left/right

side / rear corner trims. Confirm before attaching. Complete both sides.

28.

Locate and position

Side Facia Trims (4D) - 1/2” x 2 1/2” x 21 3/4”

(angle cut both ends) tight

underneath roof and against front corner door trims. Secure with

3 - 1 1/2” Finishing Nails (K).

Important -

there are left/right side facia trims. Remember the rough side of the trim faces out and

should be used as the best face. Complete both sides.

Tight against
door trims.

3 - 1 1/2”
Finishing Nails.

Tight.

Trim overhangs
rear siding by 1/2”.

Note: All Trim and Skirting pieces
are graded best face rough.

«
...
13
14
15
16
17
...
»

Summary of Contents for Garden Chalet




















Reviews:

No comments