background image

HOME

ADVANCED

OLI eBike Systems

 

| High Vision

USE

DESCRIPTION

INSTALLATION

TROUBLESHOOTING

MAINTENANCE AND 

ASSISTANCE

GENERAL 

INFORMATION

studioimmagina.com 00_102020

23

MENU

MENU

From the Home section, hold down the up + down keys 
at the same time 

 for 2 ”to enter the Menu section. 

From any screen, by holding down the power-on key 

 for 2 ”, you can return to the last viewed Home 

screen.

From the Menu page:

 ›

use the up 

 and down keys 

 to scroll through 

the items present, the selected item is highlighted 
in the centre in the white line,

 ›

press the power-on key 

 to confirm and open 

the page of the selected item, the Back item takes 
you to the first screen of the Home section.

Reset trip

Reset  

trip…

System info

SYSTEM INFO

Firmware version
HMI: 3.00.000
Motor: 2.00.000

System info

Advanced

Trip reset

Battery info

Back

MENU

Battery info

BATTERY INFO

Voltage: 39,00V
Charge cycles: 

13

Last charge: 

48h

Battery temp.:  21.0C

HOME

 ADVANCED MENU

Brightness

Language

Weight
Gender

Measure unit

ADVANCED

selected 

item

Summary of Contents for High vision







































Reviews: