background image

 

 

– Particular specifications 

25 

 

 

 

Chapter 8 

│ Particular Specifications 

Particular Specifications for use in Explosive Atmospheres in Accordance with 
the European ATEX 94/9/EC Directive.

 

 

The 

MX 15

 detection controller intended for the measurement of explosive 

gases, conforms to European ATEX Directive (94/9/CE) pertaining to 
explosive atmospheres. 

The 

MX 15

 detection controller is certified in accordance with EN 61779-1 and 

EN 61779-4 (metrological performance) as a safety device for ATEX Zone 2. 
The controller can also reduce the risk of explosion by sending data to outside 
units. 

Information in following paragraphs must be taken into account and followed 
by the person responsible for the equipment installation site. Refer to the 
provisions of European ATEX Directive 1999/92/EC, concerning the 
improvement of safety protection and the health of workers exposed to the 
risks of explosive atmospheres. 

Specifications for mechanical and electrical 
installations in Explosive Zones. 

All installations must be in compliance with currently enforced standards, 
notably standards EN 60079-14 and EN 60079-17. 

The 

MX 15

 controller must not be subject to intense mechanical vibration and 

must be installed   
in a safe area away from explosive atmospheres. 

It is very important to refer to the user and start-up manuals for the gas 
detectors being used. 

Metrological specifications 

The controller conforms to European metrological standards EN 61779-1 and 
EN 61779-4 for methane (calibration gas), butane, propane and hydrogen 
(gasses which follow response curves), where the controller is used with 

Oldham

 gas detectors as stated in the EC Declaration of Conformity (Chapter 

6). 

Where the controller is used with other types of detectors delivering a current 
of 4-20 mA, they must conform to ATEX Directive 94/9/EC, Annex II, 
paragraph 1.5 and be compatible with the characteristics described therein 
(refer to the controller transfer curve) in Figure 9. 

Note: the vibration tests described in EN 61779-4 paragraph 4.13 were not 
performed and therefore are not applicable for the operating conditions for the 

MX 15

 controller. 

Summary of Contents for MX15

































Reviews: