Old School Model Works Robin Hood 80, Construction Manual

Page: 2 / 22

Page 2 www.oldschoolmodels.com Construction Manual
WARNING
READ THROUGH THIS MANUAL
BEFORE STARTING CONSTRUCTION.
IT CONTAINS IMPORTANT WARNINGS
AND INSTRUCTIONS CONCERNING
THE CONSTRUCTION AND USE OF THIS
MODEL.
A Radio-Controlled aircraft is not a toy!
If misused, it can cause serious bodily harm
and damage to property. Fly only in open
areas, preferably at AMA (Academy of Model
Aeronautics) approved flying sites, following all
instructions included with your radio, powerplant,
electronics and batteries.
We urge you to join the AMA (Academy of Model Aeronautics) and
a local R/C club. The AMA is the governing body of model aviation
and membership is required to fly at AMA clubs.
Though joining the AMA provides many benefits, one of the
primary reasons to join is liability protection.
Additionally, training programs and instructors are available at
AMA club sites to help you get started the right way. There are
over 2,500 AMA chartered clubs across the country. Contact the
AMA at the address or toll-free phone number below:
Academy of Model Aeronautics
5161 East Memorial Drive • Muncie, IN 47302
Phone (800) 435-9262 • www.modelaircraft.org
IMPORTANT!!!
Two of the most important things you
can do to preserve the radio controlled aircraft hobby are to avoid
flying near full-scale aircraft and avoid flying near or over groups
of people.
WARNING: This product can expose you to chemicals including lead, which
is known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
INCLUDED ITEMS
Wood parts included in this kit:
• 2 - LP1 - Laser Cut 1/8” x 6” x 24” sheet
• 2 - LP2 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP3 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP4 - Laser Cut 1/8” x 6” x 24 sheet
• 1 - LP5 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP6 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP7 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP8 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP9 - Laser Cut 1/8” x 6” x 24” sheet
• 1 - LP10 - Laser Cut 1/8” x 6” x 24” sheet
• 2 - BP1 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP2 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP3 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP4 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP5 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP6 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP7 - Laser Cut 1/8” x 4” x 24” sheet
• 2 - BP8 - Laser Cut 3/32” x 4 x 24 sheet
• 2 - BP9 - Laser Cut 3/32” x 4 x 24 sheet
• 2 - 1/16” x 4” x 24” balsa sheet (uncut)
• 3/16” x 3/16” x 36” (8 pieces)
• 1/4” x 1/4” x 36” balsa strips (17 pieces)
• 1/4” x 1/2” x 36” balsa strips (5 pieces)
• 1/4” x 1” x 36” balsa strips (4 pieces)
• 3/16” x 3/8” x 36” basswood strips (9 pieces)
• 3/8” x 3/8” x 36” basswood strips (11 pieces)
• 1 - 1/4”x 6” wooden dowel.
Hardware parts included in this kit:
• 1 - Pre-bent landing gear (front)
• 1 - Pre-bent landing gear (rear)
• C/A type hinges for control surfaces
• 4 - control horns
• 4 - wheel collars 3/16” I.D.
• 4 - plastic landing gear straps
• 5 - 2-56 x 3/4” machine screws
• 20 - 2-56 x 3/4” self tapping screws
• 12 - 4-40 x 1/2” socket head cap screws
• 8 - 4-40 lock nuts
• 4 - 4-40 t-nuts (blind nuts)
• 16 steel straps
Other items included in this kit:
• 4 - Rolled plans (2 fuselage and 2 wing)
• 1 - Construction Manual
• 2 - OSMW sticker sheet
ITEMS NEEDED
Hardware needed (not included in the kit)
For some of these items there is more than one option which will
require a bit of decision making ahead of time. There isn’t a right or
a wrong choice, so choose the items that work best for you.
Resist the urge to overpower the Robinhood and remember that it
is a fun-scale model intended to fly at scale-like speeds, so prudent
throttle management should be practiced.
Here is a list of additional parts needed to complete and fly this
kit, all of which must be purchased separately. Again, we would
recommended supporting your local hobby shop.
• Powerplant:
Glow (.90-.1.50 engine, fuel tank, fuel tubing)
Gas (20cc engine, fuel tank, fuel tubing)
Electric (equivalent brushless motor, ESC, & batteries)
• Propeller