background image

                  Construction Manual 

www.oldschoolmodels.com 

Page 3

•  Engine/Motor mount and mounting hardware

•  Receiver - (4 channel minimum)

•  5 standard sized servos (4 if electric)

•  “Y” servo harness and aileron servo wire extensions.

•  Pushrods (two 5” for ailerons, two 30” for elevator & rudder, 

one 12” for throttle if glow/gas powered) 

•  Clevises for the pushrods (8 if electric, 10 if glow). Heavy duty 

4-40 hardware is recommended.

•  2 - 5” diameter wheels

•  1 - tailwheel assembly

• Covering

Additional Required Building Tools and Adhesives

•  Drill & assorted drill bits

•   Hobby knife and new, sharp blades

•   Sandpaper: coarse (80 or 100 grit) & medium (150-200 grit)

•  Pencil or pen

•   Ruler

•   String (18” length)

•   T-Pins

•  Waxed paper

•  Building board

•   6 and 30 minute epoxy

•   Adhesives of your choice. We recommend thin and medium 

CA (cyanoacrylate) viscosities

•   Epoxy brushes and mixing sticks

•   Threadlocking compound

•  Torch or soldering iron, solder and flux

•   Canopy glue

Before Starting Assembly

Closely inspect the supplied laser cut parts for damage. If you find 

any damaged or missing parts, contact us immediately. 

When removing the laser cut parts from their sheets, you’ll notice 

the parts are held in place by several small “tabs”. These tabs 

are uncut pieces of wood and can sometimes make it difficult to 

remove a part. Rather than breaking and/or splintering the wood 

by forcing out the part, we recommend removing any laser cut 

parts from their sheets by using a hobby knife with a new, sharp 

blade. A quick cut of the tab will allow the piece to be removed 

with no damage. Sand any tab remainders flush with the part so 

there will be no problem aligning them later.

It’s best to not remove parts from their sheets until they are needed. 

Refer to Appendix A of this manual as a reference to what all the 

laser cut parts look like and are called.

For each step, we highly recommend that you dry fit the parts in 

each step first. Lightly sand as needed to ensure a good fit. Once 

you’re satisfied with the fit, then and only then, glue the parts in 

position.

IT IS VERY IMPORTANT THAT YOU ASSEMBLE THIS 

ROBINHOOD 80 KIT IN THE ORDER DESCRIBED. SKIPPING 

FORWARD IN THE STEPS COULD LEAVE YOU WITHOUT THE 

PROPER LENGTHS OF WOOD TO FINISH THE KIT.

WE’VE INCLUDED ENOUGH WOOD TO EASILY COMPLETE 

THIS KIT, BUT YOU MUST TAKE CARE TO PROPERLY 

MEASURE AND NOT WASTE WOOD WHEN CUTTING.

Let’s begin construction by working on the right (starboard) 

wing of your Robinhood 80.

Prepare your work area

You’ll need a flat building surface that is a minimum of 40” long. 

Position the starboard wing plan over the surface and tape into 

position. Tear off a length of waxed paper long enough to cover 

the left wing plan and tape that into position, over the plan. 

Step 1 - Struts

This might seem like a strange 

first step in this build, but we ask 

you to do this for a reason. It’s 

to guarantee that you’ll have the 

proper lengths of 3/16 x 3/8” 

basswood.

So, gather four pieces of 3/16” 

x 3/8” and eight 3/16” square 

balsa sticks. Cut a 25-1/4” length 

from each piece and set the short 

pieces aside to use in other steps.

Take one 3/16” x 3/8” basswood piece and lay it on your board. 

Glue one of the 3/16” balsa sticks to each side of the basswood as 

shown here to make one strut assembly.

To aid in keeping these pieces straight, hold the pieces against a 

long straight-edge, such as a metal yard stick, while the glue cures.

Make 4 struts, then set them aside for much later on in the build.

Step 2 - Alignment triangles

Pre-cut into LP7 are two 

triangles, one inside the 

other. These can be used 

to vertically align any of the 

parts in the construction of 

your Robinhood 80. LP7 also 

includes two foot pieces that 

can be used with the triangles 

to hold both triangles vertical 

hands-free.

We recommend using the smaller triangle in the wing construction 

as it’s small enough to fit between the ribs.

Closely inspect the supplied laser cut parts for damage. If you find 

any damaged or missing parts, contact us immediately. 

Online Supplementary Photos

We realize that the smaller black-and-

white photos in this manual might not 

show some of the steps as clearly as 

you might want. So we’ve anticipated 

this and made these photos available 

on our website. You can either scan the 

QR code or type this address into your 

browser:

www.oldschoolmodels.com/mpics/rh80/

Summary of Contents for Robin Hood 80























Reviews: