background image

            Construction Manual 

www.oldschoolmodels.com 

Page 21

Warranty Information

Old School Model Works

 guarantees this kit to be free from defects in both 

material and workmanship at the date of purchase. This warranty does not cover 

any parts damage by use or modification. In no case shall 

Old School Model 

Works’

 liability exceed the original cost of the purchased kit. Further, 

Old School 

Model Works

 reserves the right to change or modify this warranty without notice.

In that 

Old School Model Works

 has no control over the final assembly or 

material used for the final assembly, no liability shall be assumed nor accepted for 

any damage of the final user-assembled product. By the act of using the product, 

the user accepts all resulting liability.

Limit of Liability

In the use of this product, our only obligation shall be to replace such quantity 

of the product proven to be defective.  The user shall determine the suitability 

of the product for his or her intended use and shall assume all risk and liability in 

connection therewith.

If the buyer is not prepared to accept the liability associated with the use of this 

product, the buyer is advised to return this kit immediately in new and unopened 

condition.

As of this printing, you are required to register with the FAA if you own this product.

For up-to-date information on how to register with the FAA, visit 

https://registermyuas.faa.gov .

For additional assistance on regulations and guidance of UAS usage, visit

http://www.knowbeforeyoufly.org .

For more information on all of our other products, as well as the latest news from Old School Model Works:

Please check out out website: www.oldschoolmodels.com

You can reach us on Facebook: www.facebook.com/oldschoolmodelworks

Instagram: www.instagram.com/oldschoolmodelworks/

See photos of our kits and customer builds on Flickr: https://www.flickr.com/photos/oldschoolmodelworks/

This manual is © Copyright 2023,

Old School Model Works. All Rights Reserved.

Summary of Contents for Minuette























Reviews: