manualshive.com logo in svg

Oki Teriostar LP-1040 Series, Installation Manual, Page: 59 / 91

Share
Download
Oki Teriostar LP-1040 Series Installation Manual Download Page 59

  OKI Data Infotech Corporation CONFIDENTIAL 

Chapter 7 Confirm system-wide operation and complete the hardware installation 

7-2 

7.1 

Confirm system-wide operation 

Check the entire system operation following the procedure below. 

 

(1)  Turn on the power of the Printer. 

The panel displays the standby screen. 

 

(2)  Ask the user to start the connected computer and to confirm that no issue is found with the 

computer. 

 

(3)  Ask the user to send data from each Ethernet-connected computer, and confirm that the Printer 

prints correctly. 

 

(4)  By confirming that the Printer prints correctly, complete the operation confirmation. 

If the Printer does not print correctly, again check the entire system operation again by: 

- Asking the user to recheck the connected computers' settings; and 

- Rechecking the Printer's settings. 

If an error message appears, follow the instructions displayed to solve the problem. 

Summary of Contents for Teriostar LP-1040 Series




























































































Reviews:

No comments