manualshive.com logo in svg

Oki Teriostar LP-1040 Series, Installation Manual, Page: 23 / 91

Share
Download
Oki Teriostar LP-1040 Series Installation Manual Download Page 23

  OKI Data Infotech Corporation CONFIDENTIAL 

Chapter 3 Receive the shipment and set up the Printer in the final position 

3-3 

3.1.2 

Move the Printer 

(1)  Inspect the transfer route   

Inspect the transfer route ahead of time and confirm that no obstacles are found on the route.   

 

(2)  Transfer 

The packaged Printer weighs approximately 300kg (10582.2oz) for Basic Printer Model, and 

XXX kg for Multifunction Printer Model. So move it with a forklift or dolly. If the packaged Printer 

must be moved by hand, ensure that four to six people/persons/workers are available.   

 

(3)  Important points regarding transfer 

-  If the printer must be moved by hand, ensure the appropriate safety provisions.   

-  When transferring the Printer, keep it as level as possible. If it must be tilted, do not tilt it 

30° or more.   

-  When bringing in the Printer, ensure not to damage existing equipment.   

 

 

Summary of Contents for Teriostar LP-1040 Series




























































































Reviews:

No comments