Oki OkiLAN 7300e User Manual Download Page 137

Page: 137 / 141

Troubleshooting 136

TCP/IP

Printer cannot find the network interface card.

Turn the printer off and on again.

Confirm the network interface is enabled on the printer.

Check there is a response to the

PING

command.

Check the network cable is correctly connected.

Change the cable and try again.

Run the Self-diagnostic test.

Check the IP Address, Subnet Mask and Gateway are correct.

Check that the TCP/IP protocol is set to

Enable

Reset the network interface card to factory default settings.

If DHCP, BOOTP and RARP are not used, ensure they have been set to

Disable

Cannot print with

lpr

and

ftp

Turn the printer off and on again.

Check there is a response to the

ping

command.

Check the network cable is correctly connected.

Change the cable and try again.

Check the host name and IP address are configured in the
workstation.

Check the printer port name is configured in the workstation.

There are three port names:

euc

and

sjis

. Use

by default as

euc

and

sjis

are specific to PostScript printers.

Incorrect User name on the banner page.

If printing with

lpr

, the User name printed is

unknown

and the

Filename printed is the Spool file name.

Summary of Contents for OkiLAN 7300e














































































































































Search results

Summary of Contents for OkiLAN 7300e

Reviews:

Related manuals for OkiLAN 7300e

Brands by name

Popular brands

Oki OkiLAN 7300e, User Manual

Search results

Summary of Contents for OkiLAN 7300e

Reviews:

Related manuals for OkiLAN 7300e

Brands by name

Popular brands