Oki OkiLAN 7300e User Manual Download Page 133

Page: 133 / 141

Apple Macintosh 132

Close the AppleTalk configuration page and save changes to
current configuration when prompted.

Configuration is now complete and you are ready to install your
printer driver. Please enter your driver CD, run the installer and
follow the on-screen instructions.

Macintosh OS X

The OkiLAN 7300e NIC is also supported in the Macintosh OS X
environment.

Run the installer on the driver CD to install the printer’s PPD file.

In OS X you need to make sure that AppleTalk is turned on in order to
connect to an AppleTalk printer.

To switch AppleTalk on, open [System Preferences], click
[Network] then click [AppleTalk].

Check the [Make AppleTalk Active] check box and if your network
uses AppleTalk Zones, enter the appropriate zone information
and click [Apply Now].

Summary of Contents for OkiLAN 7300e














































































































































Search results

Summary of Contents for OkiLAN 7300e

Reviews:

Related manuals for OkiLAN 7300e

Brands by name

Popular brands

Oki OkiLAN 7300e, User Manual

Search results

Summary of Contents for OkiLAN 7300e

Reviews:

Related manuals for OkiLAN 7300e

Brands by name

Popular brands