manualshive.com logo in svg

Oki C9600hdn, Network And Configuration Manual, Page: 211 / 264

Share
Download
Oki C9600hdn Network And Configuration Manual Download Page 211

 OkiLAN 8200e Network User’s Guide

211

Troubleshooting:
Novell NetWare

Printer cannot find the network print server.

•

Turn the printer off and on again.

•

Confirm that the network interface is enabled on the printer.

•

Make sure the network cable is correctly connected. 

•

Change the cable and try again.

•

If the NetWare protocol is disabled, set it to Enable.

•

Reset the network interface card to factory default settings.

The network print server is identified by the setup 

utility but not by the NetWare server.

•

Start up the NetWare server and check the NIC configuration.

•

Make sure the NSAP packet on the NetWare server is not set to Disable.

•

Make sure the correct print server is operating on the file server.

•

Make sure the Print Server name operating on the File Server and the 
Print Server name set in the NIC are the same.

•

Make sure the Printer name displayed in the Print Server monitor of the 
File Server and the NetWare Port name set in the NIC are the same. If 
there are multiple network interface cards, configure the NetWare Port 
names to be different.

Problems with Print Server mode

•

Make sure the File Server name set in the NIC and on the File Server are 
the same.

•

Make sure the Printer name set in the File Server and the NetWare Port 
name set in the NIC are the same. If there are multiple NICs, configure 
the NetWare Port names to be different. 

•

Make sure the NetWare login password is correct.

Important!

The network addresses used in this manual are shown for 
example only. Network addresses used in your installation 
must be generated from your own network.

Summary of Contents for C9600hdn









































































































































































































































































Reviews:

No comments