Okamura 865JAD Assembly & Instruction Manual Download Page 11

10

11

 

Desktop (install later)

Installation of movable shelf plate

Desk + bookshelf

For installation of the movable shelf plate, 
after installing the shelf receiving fitting pin 
of  , install the movable shelf plate, and 
tighten with the connecting bolts of   from 
the rear of the rear panel.

Installing position of the 
shelf plate is two-location 
selectable.

h

h

l

l

l

l

Tightening of bolts

Desk + bookshelf

The bolts for the movable shelf plate with drawer and the movable shelf plate can 
be tightened from both of above and below, however, tighten 

clockwise

 from 

below

 and tighten 

counterclockwise

 from 

above.

When tightening from below

When tightening from above

When tightening

from below

Tighten

* When tightening the bolt

 from 

below the shelf plate, 

turn

 clockwise.

Loosen

Tighten 

clockwise.

Tighten 

counterclockwise.

Tighten 

counterclockwise.

When tightening 

from above

Tighten

* When tightening the bolt from 

above the shelf plate, turn counterclockwise.

Loosen

Installation of movable divider

Desk + bookshelf

The movable divider can be installed to 
the desired notch part shown in the 
diagram.
Insert the plate from the notch parts on 
the right and left sides of the bookshelf 
and desk, and slide laterally to install.

Completion

Two-stage wagon drawer unit and lighting

How to store drawer unit

Securely 

tighten.

Screw-type connector
Drawer unit

Clamp with

receptacle outlet

Lighting can be installed to the notch parts on the right and left sides of the desk with a clamp.
* Refer to the “Instruction manual” attached to the illumination.

Lighting installing position

When you purchased the dedicated two-stage wagon, it is necessary to separate the drawer 
unit (upper drawer) when the desktop height is JIS No. 2 and No.3.
The separated unit can be stored in the fixed lower shelf plate as shown in the diagram.

 Separate the wagon, and remove the drawer unit and the single-end connection bolts from 

the wagon body.

 Screw the removed connecting bolts into the locations shown in 

the diagram.
* The installing location is only the right side toward the main body.

 Install the drawer unit such that the drawer front panel is directed 

upward, and turn the screw-type connectors two positions to the 
left in the clockwise direction to tighten.

(So that the front panel is directed upward)

Summary of Contents for 865JAD













Reviews: