manualshive.com logo in svg

OHAUS CD-11, Instruction Manual, Page: 15 / 30

Share
Download
OHAUS CD-11 Instruction Manual Download Page 15

PAGE 15 OF 30

0908 IH-606

H-606

17

2.7 Initial Scale Setup (Cont.)

2.7.7 Lockout Switch Menu

Lockout Switch menu (LOCSW) is a software controlled option which can lock the settings in the Calibration, Setup,

Readout, and Print menus to prevent tampering.  When used in conjunction with the Lock Switch (jumper) on the

printed circuit board, the Calibration, Setup, Readout and Print menus can be read only and not changed by an

operator.

Procedure

To select any of the items in the Lockswitch menu, pro-

ceed as follows:

NOTE

: If you have entered from the

preceeding menu, disregard the first step.

• With the Indicator ON, press and hold the

 Zero/Menu

button until MENU is displayed.  When you release

the

Zero/Menu

 button, CAL is displayed, then press

Print/Units

 button, until LOCSW is displayed.

• Press 

Zero/Menu 

button, LSTOFF is displayed.  This

permits locking the Setup menu. OFF is unlocked, ON

is read only (locked).  This menu is hidden if CAL

jumper is off.

• Press 

Print/Units

button, and select ON or OFF.

• Press 

Zero/Menu 

button, LrdOFF displayed.  This

permits locking the Readout menu. OFF is unlocked,

ON is read only (locked).

• Press 

Print/Units

button, and select ON or OFF.

• Press 

Zero/Menu 

button, LPtOFF is displayed.   This

permits locking the Print menu. OFF is unlocked, ON

is read only (locked).

• Press 

Print/Units

button, and select ON or OFF.

• Press 

Zero/Menu 

button, LCLOFF is displayed.  This

permits locking the Calibration menu. OFF is un

locked, ON is read only (locked).  This menu is hid-

den if the CAL jumper is off.

• Press 

Print/Units

button, and select ON or OFF.

• Press 

Zero/Menu

button to end this block, END is

displayed.

• Press 

Zero/Menu

 button, Quit is displayed.

• Press 

Print/Units

button to go to CAL or press 

Zero/

Menu

 button, Indicator returns to a weighing mode.

NOTE

:  At this point, the Indicator must be calibrated and

the jumper removed from the CAL connector in order to

lock out the menus. The top cover of the Indicator should

be free to gain access to the CAL jumper.

Stable Center

of Zero

Gross

    Brutto

CD-11 Indicator

18

CD-11 Indicators are equipped with a standard IBM

TM

compatible, bi-directional RS232 interface for communi-

cation with printers and computers. When the Indicator is

connected directly to a printer or Programmable Logic

Controller (PLC), displayed data can be recorded at any

time by simply pressing the 

PRINT/UNITS

 button.

Connecting the Indicator to a computer or PLC enables

you to operate several functions of the Indicator from the

computer, as well as receive data such as displayed

weight, weighing mode, stability status, etc.

2.7 Initial Scale Setup (Cont.)

2.7.8 Connecting the RS232 Interface

Hardware

 A 9-pin female “D” connector is located on the left side of

the indicator is provided for interfacing to other devices.

Pin connections are shown in the adjacent illustration.

RS-232 Pin Connections.

RS-232 Connector Pin Layout.

1

N/C

2

RXD

3

TXD

4

N/C

5

GND

6

N/C

7

N/C

8

N/C

9

N/C

CD-11 Indicator

Summary of Contents for CD-11































Reviews:

No comments