background image

 

BW SERIES COMPACT BENCH SCALE EN-11

7. CLEANING AND MAINTENANCE

      

Comply wth safety precautons when cleanng and mantanng the scale

 

•  Turn off and dsconnect the scale from the power supply durng cleanng.

 

• 

DO NOT

 open the scale; no user reparable components nsde.  Servce   

 

 

should be performed by authorzed personnel only.

 

• 

DO NOT

 place the scale upsde down.  If accessng the bottom, place the  

 

 

scale on ts sde.

 

• 

DO NOT

 carry the scale by the pan or sub-platform.  Use the handholds on  

 

 

the sdes of the scale housng.

 

• 

DO NOT

 allow lquds to enter the scale.

 

• 

DO NOT 

use hgh pressure when cleanng the scale.

 

•  Inspect the scale regularly.  Ensure that the housng, pan and sub-platform  

 

 

are clean and free from foregn materal. 

 

•  Wpe the exteror components of the scale usng a soft cloth dampened wth  

 

 

water and a mld detergent (

DO NOT

 use acds, alkals, strong solvents or  

 

 

abrasve cleanng agents).

 

•  Screw n all 4 levelng feet tghtly to avod entry of water nsde the scale      

 

  

durng cleanng.  However, when the scale s put back nto operaton, 

 

 

remember to loosen the two rear feet (and adjust levelng accordngly) to  

 

 

allow proper ar flow and mnmze condensaton nsde the scale.

 

•  Plug the rubber cap to the adapter receptacle underneath the scale to avod  

 

 

entry of water nsde the scale.

 

•  The pan s dshwasher safe and may be placed wth normal loads.  All other  

 

 

parts must not be placed n a dshwasher.

Summary of Contents for BW1.5

























Reviews: