Ofs ELEVEN WOOD Installation Instructions Manual Download Page 8 | Manualshive

Page: 8 / 8

background image

PART # 1609111

LIBRARY TACKBOARD INSTALLATION

INSTALLATION INSTRUCTIONS

ELEVEN WOOD

1. Begin by locating the through holes on the bottom of the worksurface. Next, insert the

mounting pin into the hole, making sure the longer portion of the pin is facing up. Lastly,

utilizing the pre-drilled holes in the worksurface, fasten the mount pin to the top using the

supplied screws from the HK-118 kit, as shown above.

2. With all the mount pins fully secured, the tackboard(s) can now be installed. Align the

bored holes on the bottom edge of the tackboard to the mount pins and drop the tackboard

into position. NOTE: The optional Powdercoated Standoff will need to be slid onto the pins prior

to the tackboard, as shown above.

THROUGH HOLE

MOUNT PIN

OPTIONAL

STANDOFF

«
...
6
7
8

Summary of Contents for ELEVEN WOOD









Reviews:

No comments

Related manuals for ELEVEN WOOD

Brand: nardi Pages: 2

Brand: Officeworks Pages: 15

Brand: OBaby Pages: 14

Brand: Oakworks Medical Pages: 28

Brand: Watermark Pages: 2

Brand: HAMPTON BAY Pages: 14

Brand: &Tradition Pages: 3

Brand: µ-Dimension Pages: 4

Brand: &Tradition Pages: 4

Brand: µ-Dimension Pages: 5

In Between SK23

Brand: &Tradition Pages: 3

Hee Welling Drip HW61

Brand: &Tradition Pages: 5

Brand: µ-Dimension Pages: 2

SPACE COPENHAGEN AMORE SC Series

Brand: &Tradition Pages: 2

Brand: µ-Dimension Pages: 4

Brand: &Tradition Pages: 3

Brand: µ-Dimension Pages: 3

SHUFFLE TABLE MH1

Brand: &Tradition Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands