Ofs 432 Installation Manual Download Page 7

Issue2 

November 14, 2011 

 

- 6 - 

 

Warnings 

 

Important safety warnings are used throughout this manual for possible hazards to 
persons and equipment.  A warning identifies a possible hazard and then explains what 
may happen if the hazard is not avoided.  These cautions should be followed at all times.  
These warnings are flagged by use of triangular alert icon (see below) and are listed in 
descending order of severity of injury or damage and likelihood of occurrence. 
 
 

 

 

 
Inspecting Shipment 
 

Upon receipt of the equipment, following the following instructions: 
 

(1)

 

Inspect the shipping containers and note any signs of damage.   

 
(2)

 

Unpack the containers and carefully inspect the contents for damage.  

 
(3)

 

If the equipment has been damaged in transit, immediately report the extent 
of the damage to the transportation company and to OFS.  Order replacement 
equipment if necessary. 
 

(4)

 

Check the packing list to ensure complete and accurate shipment of all listed 
items. 

 
(5)

 

If the packing list is irregular or deficient in any way, please contact OFS as 
described in the Warranty agreement. 

 

(6)

 

Prolonged storage of the equipment should be done the original container. 

 

(7)

 

Product returns should use the original packaging if available. 

 

 

Replacement and Accessory Kits 
 

See Table 1 for replacement and accessory kit details.  See your local OFS account 
representative for order details on the accessory kits. 
 
 

 

Summary of Contents for 432



















Reviews: