manualshive.com logo in svg

OfiTE MB HTHP, Instruction Manual

Share
Download
OfiTE MB HTHP Instruction Manual Download Page 3

The OFITE Model MB HTHP Filter Press is designed to test drilling fluids
and cement under elevated temperatures and pressures.  This simulates
various downhole conditions and provides a reliable method for determin-
ing the effectiveness of the material being tested.  The complete assembly
consists of a controlled pressure source, regulators, a high pressure cell, a
system for heating the cell, a pressurized collection cell able to maintain
proper back pressure in order to prevent flashing or evaporation of the fil-
trate, and a suitable stand.

Size:

19" x 21" x 28" (49 x 54 x 72 cm)

Weight:

40 lbs. (18.2 kg)

Shipping Size:

23" x 13" x 13" (59 x 33 x 33 cm)

Shipping Weight:

50 lbs. (22.8 kg)

Maximum Temperature:

350°F (176°C)

Maximum Pressure:

1,500 PSI (10,342.5 kPa)

Pressure Source:

2 CO

2

Cartridges

Test Cell Capacity:

250 mL

Voltage:

#171-50: 115V; #171-51-C: 230V

Heater:

200 Watt

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

2

Specifications

Intro

Summary of Contents for MB HTHP













Reviews:

No comments

Brands by name

Popular brands

Load more brands