background image

 8 

 

4.

 

Start-up / Shut-down

 

Before Start-up:

 

 

Read and observe operation manual. 

 

In order to guarantee proper function and trouble-free operation, the 
following checks to be carried out before start-up: 
 

  General condition of the unit (connections, gaskets, etc.). 

 Power 

cables/connections. 

  High pressure hoses, hose pipes, whether damaged. 

  Air supply, fresh air grill must not be covered. 

  Filling of consumables. 

  Correct oil level of high pressure pump (sight glass/dip stick).  

  High pressure pump: OERTZEN OSP special pump oil.  

  Pump/pump connections whether leaking. 

  Machine only to be run with absolutely clean water. Before connecting 

the water supply hose, rinse it thoroughly. Depending on feed water 
quality, regularly check water filter in short intervals, replace if needed. 

  Machine only to be run horizontally (+/- 5°). 

 

In order to guarantee proper function and trouble-free operation, the 
following checks to be carried out during working: 
 

  Observe function of indicator lights and monitors. 

  Observe pressure variations 

  Observe leaks at high pressure pump, hose pipes, connections. 

  Observe unnormal noise. 

 
In case of malfunctions immediately stop machine, eliminate cause according 
to chapter „Trouble Shooting“, call qualified service. 

 

Connections 
 

Water Supply 
Connect water inlet (6) of the machine to water source with a clean hose 
(diameter see table below). Before connecting water supply hose, rinse it 
thoroughly. In case of connection to the potable water distribution, observe 
DIN 1988 (for momentary connections use a backflow preventer with non-
return function and ventilation). 
 

 

Flow pressure 

Min. flow rate * 

minimum:  2 bar 

 15 l/min 

"    water supply hose 

maximum: 8 bar 

 21 l/min 1"     water supply hose 

 

 30 l/min 1 

" water supply hose 

 

* s. Techn. Data 

 
Insufficient water supply will cause heavy damage on high 
pressure pump (cavitation). 

 

 

 

 

Summary of Contents for E 500-17
















Reviews: