background image

13

18/03/2016 - 300020192-02

PK 550

4. 

Installation

4.3 Hydraulic connections

4.3.1

Dimensional information required

Draining outlet 3/4’’

Heating return:

- 9 to 17 sections: 139.7 - 5"
- 18 to 25 sections: 159 - 6"
weld.

Heating flow: 

- 9 to 17 sections: 139.7 - 5"
- 18 to 25 sections: 159 - 6"
weld.

* dimension without connection (see figure on chapter Boiler location,
straight or angled connection).

4.3.2

Important recommendations for connecting the boiler to the heating circuit

Installation must be carried out in accordance with the prevailing regulations, the codes of practice and the recommendations in these
instructions.

France:

Heating installations must be designed and constructed in such a way as to prevent the return of water in the heating circuit and the products
put into it into the drinking water network located upstream; The installation must not be connected directly to the drinking water network (article
16-7 of the local health directive). When these installations are fitted with a filling system connected to the drinking water network, they comprise
a CB disconnector (disconnector for zones with non-controllable pressure differences) which satisfy the functional requirements of the NF P
43-011 standard.

`

Minimum safety valve flowrate as a function of maximum boiler nominal output:

Minimum relieving capacity

Maximum gross boiler output

(a) = kW, (b) = lb/h, (c) = MBtu/h, (d) = Kg/h

Example

Maximum boiler nominal output is 800 kW.
Minimum safety valve flowrate must be 2600 Kg/h.

There must be no total or partial closing mechanism
between the boiler and the safety valves (France: DTU -
65.11, § 4.22 - NF P 52-203).

C

1080mm

H*

   

  D

     

M000034

1

2

3

0

m

2 0

m

Boiler

PK 

550-9

PK 

550-

10

PK 

550-

11

PK 

550-

12

PK 

550-

13

PK 

550-

14

PK 

550-

15

PK 

550-

16

PK 

550-

17

PK 

550-

18

PK 

550-

19

PK 

550-

20

PK 

550-

21

PK 

550-

22

PK 

550-

23

PK 

550-

24

PK 

550-

25

C (mm)

1488 1488 1488 1488 1488 1488 1488 1488 1488 1504 1504 1504 1504 1504 1504 1504 1504

D (mm)

212

233

234

255

256

217

188

189

210

236

257

208

209

230

231

252

253

H (mm)

-7

14

15

36

37

-2

-31

-30

-9

-8

13

-36

-35

-14

-13

8

9

Summary of Contents for PK 550

































Reviews: