background image

2

TABLE OF CONTENTS

Thank you for purchasing the O’Donnell SS .21 engine. Many years 
of engine expertise were used to develop an engine with maximum 
performance and reliability. This engine was manufactured using the 
highest quality standards, materials and manufacturing processes. 
When properly used and maintained, it will perform at the highest 
level of racing. Carefully read through the entire instruction manual 
before starting your SS .21 engine.

 Safety 

Precautions 

.......................... 3

 Important 

Information 

...................... 4

 Fuel 

................................................. 5

 Fuel 

Tubing 

...................................... 5

 Fuel 

Filter 

........................................ 5

 Air 

Filter 

........................................... 6

 Glow 

Plug 

........................................ 6

 Tuned 

Pipe 

...................................... 7

 Carburetor 

Restrictors 

..................... 7

 

High Speed Needle ......................... 8

 

Low Speed Needle .......................... 8

 

Throttle Stop Screw ......................... 8

 

Factory Carburetor Settings ............ 8

 

Priming the Engine .......................... 9

 Engine 

Break-In 

............................ 10

 Engine 

Maintenance 

..................... 12

Summary of Contents for SS .21

















Reviews: