background image

39 of 44

Subject to change without notice

OC15269 REV F

www.octopusdrives.com

www.octopuseurope.com

C2b Connection - Simrad Autopilots

The RFB Module OC15SUK27D

 must

 be used in conjunction with the Signal 

Conversion Module OC15SUK83 when integrating with Simrad Autopilots.

i) 

important

 - all wiring connections must be made between the RFB 

Module, the Signal Conversion Module and the Autopilot Course Computer 

beFore

 powering up the Course Computer.  Failing to follow this will result 

in the RFB signal not being recognized by the Course Computer.  If this 

occurs perform the “Autopilot Reset” procedure (refer to Simrad autopilot 

manual).

ii)  Determine suitable site to mount the Signal Conversion Module.  Shorten or 

insert suitable extension cable as required to suit the installation.

iii) Connect the RFB Module, Signal Conversion Module and Autopilot Course 

Computer together as shown in Fig C4.  Use a marine grade electrical con-

nection strip and ensure the wires are properly insulated and protected.

iv) Connect Octopus Signal Conversion Module output wires to Auto Pilot 

Junction Box following Auto Pilot installation and wiring diagram.  

v)  Setup and calibrate the RFB as described in section B10. 

Fig C4 - RFB connections - Simrad Autopilots

Summary of Contents for 44364













































Reviews: