background image

• Attach the steering cable to the tiller

i)  Rotate the steering cable rod end so 

that the hole is horizontally aligned.

ii)  Position the steering cable rod end 

into the clevis bracket (Fig B43).

iii) Insert the quick release locking pin 

and lock in place using the hitch pin.

• Refer to section B9 on connecting the secondary steering cable to the drive unit.

B7d Quick Release

In an emergency situation the steering cable can be quickly disconnected from the

tiller by pulling out the hitch pin and then removing the locking pin.

B7e Specification

Maximum stroke .......................................................... 8.5in (216mm)

Peak Thrust ................................................................. 330Ibs / 136kg

Max Rudder Torque..................................................... 185ft-lb (250Nm)

Hard Over Time ........................................................... 12-15 seconds

Peak Power ................................................................. 60 watts 5 amps

Average Power ............................................................ 1.25 amps

Tiller arm radius ........................................................... 7.5in /190mm

Max displacement ........................................................ 13,200Ibs / 6,000kg

Max boat length ........................................................... 32ft / 10m

Voltage......................................................................... 12V DC
Clutch circuit power ..................................................... 850mA

32 of 44

Subject to change without notice

OC15269 REV F

www.octopusdrives.com

www.octopuseurope.com

Fig B43 - Attaching the steering cable to the tiller

Hitch pin

Quick release

locking pin

Summary of Contents for 44364













































Reviews: