Octave V 80 SE Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 48

background image

17

4. OPERATION

Legend



Remote control receiver

To ensure optimum operation of the IR remote control, do not cover
this window.



Status indicators

Protection Red LED lights up when the electronic protection

system has switched the amplifier off in response to an
amplifier fault. (See Chapter 9)

Soft-start Lights up during the soft-start process immediately

after switch-on. This LED goes out after about 1
minute when soft-start has been completed. (See
Chap. 3.4. + Chap. 7.4. + Chap. 7.5.)

Extern

Illuminates to indicate separate pre and power
amplifier operation. (see Chapter 7.2.)

Headphone Illuminates when headphones are connected.

(See Chapter 7.5.)



Front Ch.

Illuminates when multichannel-bypass function is on.
(See Chapter 6.7.)



Ecomode

Illuminates when Ecomode/power saver mode is on.
(See Chapter 7.4.)



Mode selector knob

Linear

Pre and power amplifier are connected internally.
(Chapter 7.1.)

Extern

Pre and power amplifier are separate.

(See Chapter 7.2.)



BIAS The electronic bias measurement system is on and the LED

array shows the power tubes' idle current.
(See Chapter 8.3.)



Volume control

Remote controlled motorized potentiometer

«
...
14
15
16
17
18
...
»

Summary of Contents for V 80 SE

















































Reviews:

No comments

Related manuals for V 80 SE

Brand: Nakamichi Pages: 34

Brand: Hamilton/Buhl Pages: 16

Brand: Hamilton Electronics Pages: 5

Brand: GOODWOOD AUDIO Pages: 4

Brand: ifi Pages: 33

Brand: Toa Pages: 1

HA2401RTGX-1000

Brand: l-com Pages: 3

Brand: Unika Pages: 16

Brand: Bugera Pages: 15

Pacemaker 30200

Brand: CSP Products Pages: 12

Brand: Radio Systems Pages: 13

Brand: Audiolab Pages: 34

Brand: APART Pages: 16

Brand: Ampetronic Pages: 12

Brand: ATEN Pages: 2

1812R Blues King 12

Brand: SUPRO Pages: 8

Road Thunder RT1000-1D

Brand: MTX Pages: 48

Brand: Crest Audio Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands