manualshive.com logo in svg

Octagon 5554, User Manual

Share
Download
Octagon 5554 User Manual Download Page 35

WARRANTY

Octagon Systems Corporation (Octagon), warrants that its stan-
dard hardware products will be free from defects in materials and
workmanship under normal use and service for the current
established warranty period.  Octagon’s obligation under this
warranty shall not arise until Buyer returns the defective product,
freight prepaid to Octagon’s facility or another specified location.
Octagon’s only responsibility under this warranty is, at its option,
to replace or repair, free of charge, any defective component part of
such products.

LIMITATIONS ON WARRANTY

The warranty set forth above does not extend to and shall not
apply to:

1.

Products, including software, which have been repaired or
altered by other than Octagon personnel, unless Buyer has
properly altered or repaired the products in accordance with
procedures previously approved in writing by Octagon.

2.

Products which have been subject to power supply reversal,
misuse, neglect, accident, or improper installation.

3.

The design, capability, capacity, or suitability for use of the
Software.  Software is licensed on an “AS IS” basis without
warranty.

The warranty and remedies set forth above are in lieu of all other
warranties expressed or implied, oral or written, either in fact or
by operation of law, statutory or otherwise, including warranties of
merchantability and fitness for a particular purpose, which
Octagon specifically disclaims.  Octagon neither assumes nor
authorizes any other liability in connection with the sale, installa-
tion or use of its products.  Octagon shall have no liability for
incidental or consequential damages of any kind arising out of the
sale, delay in delivery, installation, or use of its products.

SERVICE POLICY

1.

Octagon’s goal is to ship your product within 10 working days
of receipt.

2.

If a product should fail during the warranty period, it will be
repaired free of charge.  For out of warranty repairs, the
customer will be invoiced for repair charges at current stan-
dard labor and materials rates.

3.

Customers that return products for repairs, within the
warranty period, and the product is found to be free of defect,
may be liable for the minimum current repair charge.

Summary of Contents for 5554





































Reviews:

No comments

Brands by name

Popular brands

Load more brands