background image

6.5 Unpairing the remote control (Bluetooth mode)

When you replace the remote control with a new one or reset the paired remote

control to the factory settings, you have to unpair the remote control from the set-

top box.
1. In the user interface of the IPTV system, go to the 

Einstellungen > Fernbedi-

enung

 screen or press the setup-button.

2. Follow the instructions to unpair the remote control.

The set-top box restarts.
The screen for pairing the remote control is shown.

3. Follow the instructions to pair the remote control.

6.6 Resetting the remote control

When you reset the remote control to the factory settings, you also have to

unpair the remote control from the set-top box (see Section "Unpairing the

remote control (Bluetooth mode)" on page 18). Only then can you pair a

remote control with the set-top box again (see Section "Pairing the remote

control" on page 7).

To reset the remote control to the factory settings, proceed as follows:
1. Press and hold down the red and blue function buttons simultaneously for at

least 5 seconds.

The green LED on the remote control flashes twice in quick succession.

2. Enter the digits 

9999

.

If the green LED flashes twice in quick succession, the remote control has

been reset to the factory settings.

The remote control is in Bluetooth mode. The Bluetooth connection to the set-top

box and the programmed TV code (if any) have been erased.

18 | P510E IP

Summary of Contents for P510E IP





























Reviews: