Warning: Product installation and operation
Before installing the OceanBridge, read and follow all
warning notices and instructions which are included.
Failure to follow safety warnings and instructions can
result in property damage, severe injury or even death.
Warning: Power supply voltage
Connecting this product to a voltage supply greater than
the specified maximum rating may cause permanent
damage to the unit. Refer to the Technical Specification
section for voltage rating.
Warning: Hazardous or flammable atmospheres
This product is NOT approved for use in hazardous or
flammable atmospheres. DO NOT install it in areas with
hazardous or flammable atmospheres, such as engine
rooms or near fuel tanks.
Danger: Risk of electric shock or electrocution
This OceanBridge unit must be installed by a licensed or
certified electrician in accordance with all applicable local
codes and ordinances. Improper installation will create
an electrical hazard which could result in death or serious
injury to swimmers, installers, or others due to electrical
shock, and may also cause damage to property.
Warning: Switch off power supply
Ensure the vessel’s power supply is switched OFF before
starting to install this product. Do NOT connect or discon-
nect equipment with the power switched on.
IMPORTANT INFORMATION
CAUTION: Power supply protection
When installing this product and using the OceanLED
power cable, make sure the power source is adequately
protected by using a suitably-rated fuse or automatic
circuit breaker.
Water ingress disclaimer
Although the waterproof rating capacity of this product
meets the IP66, water intrusion and subsequent equip-
ment failure may occur if the product is subjected to,
such as but not limited to, high-pressure washing and/or
submersion/flooding. OceanLED will not warrant products
if the cause of failure is greater than the requirements for
IP66 rating.
EMC installation guidelines
OceanLED equipment and accessories conform to
the appropriate Electromagnetic Compatibility (EMC)
regulations, to minimize electromagnetic interference
between equipment and minimize the effect such
interference could have on the performance of your
system.
FCC Compliance
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure Guidelines.
This equipment should be installed and operated keeping
the radiator at least 20cm or more from the person’s
body.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Caution
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This device complies with below part 15 of the FCC Rules.
• Part 15 Subpart C
• Part 15 Subpart E
Warning: USB connection
The OceanBridge product is equipped with a USB data
connection specifically intended for the connection of
USB memory storage devices. Please DO NOT attempt to
connect devices with AC power sources, such as PCs or
Laptops, to the OceanBridge product using the USB port.
This port is exclusively designed for USB memory storage
devices only to ensure safe and optimal functionality.
Product disposal
Dispose of this product in accordance with the WEEE
Directive.
Caution: Service and maintenance
This product does not contain user-serviceable
components. Please direct all maintenance and repair
inquiries to authorized OceanLED dealers. Unauthorized
repairs could impact your warranty.
Unit cleaning instructions
The unit does not require regular cleaning. However, if you
find it necessary to clean the unit, please follow the steps
below:
1. Ensure power is switched off.
2. Wipe unit clean with a damp cloth.
3. If necessary, use a mild detergent solution to remove
grease marks.
Technical accuracy
To the best of our knowledge, the information in this
document was correct at the time it was produced.
However, OceanLED cannot accept liability for any
inaccuracies or omissions it may contain. Please
check the OceanLED website (www.oceanled.com) to
ensure you have the most up-to-date version(s) of the
documentation for your product.
SAFETY NOTICES:
Ocean LED Marine LTD / Tel +44 (0) 1455 637505 / [email protected]
Ocean LED USA LLC / Tel +1 954 523 2250 / [email protected] /
www.oceanled.com
Specifications are subject to change without notice.
