background image

EXPLORE 

E3

.

 

 

2021 INSTALL & OPERATION MANUAL 

 
 

19 

 

5.6 LIGHT CARTRIDGE REMOVAL 

– EXTENDED MOUNTING TUBE  

 
Before  proceeding  with  this  operation,  you  MUST  seek  permission  from  either  the  manufacturer  or  your 
OceanLED representative. 
 
DO NOT remove the light cartridge from the mounting tube during installation. The light cartridge MUST stay 
fitted  inside  the  mounting  tube  throughout  the  installation  process  to  avoid  the  introduction  of  potential 
contaminants that may damage the product. 
 

Additional items required not supplied by OceanLED: 

 

T-Handle Allen key (2mm) 80mm length. 
 

1.  If the vessel is in water check that the front glass is present and intact.  Never remove a cartridge with the 

vessel in water if damage to the glass lens is suspected. 

2.  Turn power off and unplug all the connector on the back of the light. 
3.  Remove the locking ring and the compression tube from the mounting tube. 
4.  Undo and remove one of the six screws from the back of the light cartridge to ease removal. 
5.  Loosen the other 5 screws by the same height (approx. 15-20 full rotations of the Allen key) without removing 

them.   

6.  Insert the explore extended removal tool into the mounting tube ensuring the cut-outs in the tool align with the 

screws. Twist the tool to align.  
 

 

 

 

 

 

 

 

 

 

7.  Twist the tool to engage the screw heads. Once the screw heads are engaged twist and pull the tool outwards 

to extract the light. 

 

 

 

 

 

 

 

 

 

 

Not engaged 

Engaged 

Summary of Contents for EXPLORE Series






























Reviews: