Oceanled A12PRO Installation Manual Download Page 16

16

16

4

CHAPTER

FOUR

Chapter 4: Warranty Statement:

This warranty statement is for those products supplied to and sold from all territories 

internationally 

OceanLED stands by its products. In general terms, the company gives a full 2 year’s manufacturer’s 

warranty on all of its products from date of sale. 
To claim, please contact an authorised OceanLED dealer and complete the troubleshooting guidelines 

and warranty claim form (available from www.oceanled.com). Claims may be disputed if the 

troubleshooting guidelines are not completed or no defect is found with the product. The detailed terms 

and conditions of this warranty are set out below.
However; please note that all metal parts corrode in salt water. The primary factors affecting corrosion 

are not directly related to our products and accordingly OceanLED cannot be held responsible for 

corrosion-related defects this includes where water has been allowed to enter the cable as a result of 

immersion in water during the installation or improper sealing of connections.  Please note corrosion will 

be particularly aggressive if installation and/or bonding have not been undertaken properly; or if stray 

currents are active in the vicinity of a boat.
Colour variation occurs within the LED manufacture. While we make every effort to match the colour of 

any lights there may be a noticeable difference when installed next to existing lights. OceanLED does not 

warrant this colour variation on lights.
OceanLED reserves the right to change the design, range and components without any prior notification 

either written or verbal.

1: WARRANTY OF QUALITY

1.1 

In the case of goods manufactured and sold by OceanLED Marine LTD, a company incorporated in 

England and Wales (registered number 08927130) and whose registered office is at Unit 1 Jacknell 

Road, Dodwells Bridge Ind. Est. Hinckley, Leicestershire, LE10 3BS (the “Goods” and the “Company”, 

respectively), the Company warrants to the purchaser of the Goods (the “Buyer”) Conditions and 

unless otherwise notified). That (subject to the other provisions of these. The Goods supplied shall 

be of satisfactory quality within the meaning of the Sale of Goods Act of 1979.

1.2  the Company shall not liable for a breach of the warranty in Condition 1.1 unless:
1.2.1  the Buyer gives written notice of the defect to the Company, and to the carrier if the defect is as a 

result of damage in transit, within 14 days of the time when the Buyer discovers or ought to have 

discovered the defect; and

1.2.2  the Buyer has the obligation to provide all the requested information where is reasonably possible 

and provided a truthful statement of all information requested in relation to the claim.

1.2.3  the Buyer returns such Goods to the Company’s place of business at the Buyers cost, regardless of 

the outcome of the claim.

1.2.4  the Company is given a reasonable opportunity after receiving the returned Goods for the 

examination to take place at the Company’s place of business. 

1.3  the Company shall not be liable for a breach of the warranty in Condition 1.1 if:
1.3.1  the Buyer makes any further use of such Goods after giving such notice; or
1.3.2  the defect arises because the Buyer failed to follow the Company’s oral or written instructions as to 

storage, transportation, installation, commissioning, modification, use or maintenance of the Goods 

or (if there are none) good trade practice; or the defect arises from the corrosion of metal parts or 

OceanLED INSTALL / AMPHIBIANS / 053014 / v4.2

Summary of Contents for A12PRO

























Reviews: