background image

iv

Precautions 

• 

This camera should be installed by qualified personnel only.

• 

There are no user serviceable parts inside.

• 

Do not disassemble this camera other than to make initial adjustments.

• 

Use a UL approved regulated 12 volt DC power supply.

• 

Use appropriate low voltage power cable to prevent fire or electrical shock.

• 

Please insure that your installation area can support the weight of the camera. 

Handle this camera carefully

• 

Do not use a strong or abrasive detergent when cleaning the camera. 

• 

Do not install near cooling or heating devices.

• 

Do not install the camera in extreme temperature conditions.

 

Use the camera in environments where temperature 

is within 14°F to 122°F. Use adequate ventilation if a camera is installed where high temperatures may occur.

• 

Do not install or use the camera in an environment where the humidity is high.

 

Very high humidity levels can 

reduce image quality.

• 

Do not install the camera under unstable lighting conditions. 

Severe lighting change or flicker can cause the camera 

to work improperly.

• 

Do not touch the front lens of the camera. 

Finger prints, dust and soil on the front glass can cloud the video image and 

reduce the effectiveness of the IR array. 

• 

Do not drop the camera or subject it to physical shocks.

• 

Do not expose the camera to rain or spill liquids on it.

 

If it gets wet, wipe dry immediately. Liquids can contain 

minerals that corrode the electronic components.

• 

Do not expose the camera to radioactivity. 

If exposed to radioactivity the video sensor may fail.

• 

Do not disassemble the camera.

 

There are no user-serviceable parts inside it.

• 

Do not drop the camera or subject them to physical shocks.

 It can cause malfunctions to occur.

• 

Never point the camera at a strong light, or exposing it to a spotlight or an object reflecting the strong light.

 

Smear or blooming may occur, and it can damage the CCD.

• 

Before applying power to the camera, check the power source to ensure that it is within specifications.

 

Summary of Contents for BC600 Series

















Reviews: