background image

ii

WARNING

!

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the camera. 

 

CAUTION

To prevent electric shock and risk of fire hazards, do NOT use other than the specified power source. 

REGULATORY NOTICE 

These cameras comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and  

(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. 
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and use in 

accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in which case the user will be 

required to correct the interference at his own expense.
These cameras are CE and RoHS compliant. 

 

LEGAL NOTICE 

Observint

 

Technologies

 (

Observint

) products are designed to meet safety and performance standards with the use of 

specific 

Observint

 authorized accessories. 

Observint

 disclaims liability associated with the use of non-

Observint

 

authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly 

prohibited by law.

Observint

 makes no representations concerning the legality of certain product applications such as the making, 

transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We 

encourage you to check and comply with all applicable local, state, and federal laws and regulations before 

engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks 

and names or their products. 

Observint

 disclaims any proprietary interest in trademarks and trade names other than 

its own.
No part of this document may be reproduced or distributed in any form or by any means without the express written 

permission of 

Observint

© 2013 Observint Technologies. All Rights Reserved.

 

11000 N. Mopac Expressway, Building 300, Austin, TX 78759 

For Sales and Support, please contact your distributor. 

Summary of Contents for BC600 Series

















Reviews: