background image

28

308–030

ACCESSORIES

MUST BE PURCHASED SEPARATELY

French

185–955

Spanish

185–962

German

186–042

Greek

186–046

Korean

186–050

English

185–954

Apply other

language in this area on

other side of shroud

DANGER LABELS
The English language DANGER label shown on
page 1 is also on your sprayer. If you have paint-
ers who do not read English, order one of the fol-
lowing labels to apply to your sprayer. The drawing
below shows the best placement of these labels
for good visibility. Order the labels directly from
Graco, free of charge.

Toll Free: 

1–800–328–0211

DISPLACEMENT PUMP REPAIR KIT

222–587

See contents on page 27.  Repair instructions are 
included with the kit.

THROAT SEAL LIQUID
Non–evaporating liquid for the wet–cup. Helps prevent
buildup of paint on the rod and throat packings, 
to reduce premature wear.

206–994

8 oz.

206–995

1 quart

206–996

1 gallon

SPRAY HOSES

223–541

1/4” ID; 50 ft. (15 m); coupled 1/4 npsm (f);
spring guards on both ends
3300 psi (231 bar) Max. Working Pressure

214–701

3/16” ID; 3 ft. (0.9 m); coupled 1/4 npsm (f);
spring guards on both ends
3300 psi (231 bar) Max. Working Pressure

FLUID FILTER KIT

223–857

Includes a fluid filter and all necessary mounting hard-
ware.

REVERSE-A-CLEAN

t

 IV 

Dripless

t

TIP GUARD 220–422

Uses fluid pressure from the gun to  remove clogs 
without removing the tip guard to spray tip. 

(As shown

on guns, below

.) Requires SwitchTip

t

, purchased 

separately.
 

“SILVER” GUN

220–954

5000 psi (350 bar) MAXIMUM
WORKING PRESSURE
Includes Reverse–A–Clean IV DripLess

t

Tip Guard and 517 size SwitchTip

t

“CONTRACTOR” GUN

220–955

3600 psi (252 bar) MAXIMUM
WORKING PRESSURE
Includes Reverse–A–Clean IV DripLess

t

Tip Guard and 517 size SwitchTip

t

“BLACK MAX” GUN

220–730

3600 psi (252 bar) MAXIMUM
WORKING PRESSURE
Includes Reverse–A–Clean IV DripLess

t

Tip Guard and 513 size SwitchTip

t

WHEEL KIT

223–822

Converts the PRO301 mounting frame to a portable cart.

EXISTING FRAME

Includes all parts
shown except frame

Summary of Contents for PRO 301

































Reviews: