Oben Skysill CFT-6194L Skysill CTF-6394 Manual Download Page 18

Page: 18 / 20

WARNINGS / OPTIONAL ACCESSORIES

Warnings:

• Do not exceed the tripod’s maximum load

capacity.

• Ensure that all appropriate locks are

engaged when necessary.

• The tripod should be used only in

temperatures between -22°F and 140°F
(-30°C and 60°C).

• Do not operate in salt water. Dry the tripod

off if it becomes wet.

• Remove the camera from the tripod during

transport.

• Keep out of reach of children.

• Always support the camera on top of

the center column with one hand while
adjusting the center column’s height.

OPTIONAL ACCESSORIES

Oben Tripod Strap with Quick-Release Loop and
Spring Lock

• TS-10

• TS-100

Oben Deluxe Tripod Strap with Swivel Clip

• TS-110

Oben Tripod Strap with Two Quick-Release Loops

• TS-20

• TS-200

Oben Tripod Hammock

• STB-10

Visit our website at

ObenSupports.com

for more Oben products.

Summary of Contents for Skysill CFT-6194L Skysill CTF-6394




















Search results

Summary of Contents for Skysill CFT-6194L Skysill CTF-6394

Reviews:

Related manuals for Skysill CFT-6194L Skysill CTF-6394

Brands by name

Popular brands

Oben Skysill CFT-6194L Skysill CTF-6394, Manual

Search results

Summary of Contents for Skysill CFT-6194L Skysill CTF-6394

Reviews:

Related manuals for Skysill CFT-6194L Skysill CTF-6394

Brands by name

Popular brands