Oasis Ace MAX Series Instruction Manual Download Page 20

20

Ace Pump Corporation   

   P.O. Box 13187 - 1650 Channel Avenue   

   Memphis, TN  38113

www.AcePumps.com   

   Phone:  901-948-8514    

    Fax:  901-774-6147

Ace Form # HYD-MAN MAX

Revised 12/16

STANDARD WARRANTY

Ace pumps and valves are guaranteed against defects in material and workmanship for a 

period of one year from date of installation.  The warranty period is two years for pumps 

equipped with Oasis

 WetSeal Technology which requires proper maintenance of the 

seal chamber by the user as directed in the Instruction Manual.  Products or parts found 

to be defective upon inspection at the factory will be repaired or replaced at our discretion.

Ace Pump Corporation shall not be held liable for damages caused by abuse or misuse 

of the product or parts.  No claim for labor in repairing or replacing such products will be 

allowed nor will loss of time or inconvenience be considered warranty obligations.

IMPORTANT:  Pumps or valves returned for warranty consideration which are tested and 

found to perform within specifications are subject to an inspection charge.

PLEASE NOTE EXCEPTIONS

All seals are covered against defects in materials or workmanship.  Seal failures resulting 

from application related conditions are not covered.  Most seal failures are due to application 

conditions such as:  (1) abrasive solution scratching the polished seal faces;  (2) chemical 

attack on elastomer or glue; (3) thermal shock from running pump dry or improper priming; 

(4) failure to flush chemical from pump after use.

Repair requests under the above category will not be considered warranty, and current 

repair and transportation charges will apply.

PROCEDURE

To return a pump, valve, or part for warranty consideration, please call Ace Pump and 

request a Returned Goods Authorization (RGA) number (800-843-2293).  Please request 

one RGA number for each pump or valve.  Provide the part number of the item being 

returned along with the reason for return.  Be specific when describing the nature of the 

defect.  Include this information in the box along with a customer contact name, phone 

number,  and  return  address.    Ship  pump  prepaid  freight.    Package  pump  in  original 

packaging or similar to prevent damage in shipment.  Warranty determinations will be 

made after the product has been received and inspected.

This warranty is in lieu of all other warranties, express or implied, and Ace Pump Corporation 

does not authorize any other person to assume for it any obligation or liability in connection 

with the sale of said pumps, valves, or any parts thereof.

WARNING:  Pumps returned to Ace must be free of chemical hazard.  Chemicals must 

be neutralized and thoroughly rinsed.  Pumps with indications of active chemical will not 

be considered for repair or warranty.

Summary of Contents for Ace MAX Series





















Reviews: