OAKWORKS Clodagh Leo User Manual Download Page 5

The Table is designed to be a stand-alone table. This table must not be modified or incorporated into any other 

equipment. 
As with any moving mechanism there are potential pinch points around and underneath the table.  It is the 

responsibility of the operator of this equipment to insure that bystanders are not in the area below or around this 

equipment during operation.  
Proper operation of this equipment is very important for the safety of the operator, client, and any other  

individuals in the area of this equipment.  Directions for use of this equipment are described in this manual.   

The operator should read these sections carefully.

Weight Limit: (client and accessories) 500 lbs. (227 kg) Do not exceed.

Be certain that the table is completely lowered prior to discharging an ambulatory client. The client may lose bal-

ance and fall.

This table is not suitable for use in the presence of flammable anesthetic mixture with air or oxygen or 

nitrous oxide.

Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 

Do not lift table by the table top. This can damage the table.
When lowering the table, make sure there is nothing underneath the table top that can impede motion (like 

stools, cabinets, accessory parts, cleaners, etc)

Use this furnishing only for its intended use as described in these instructions. Do not use attachments not  

recommended by the manufacturer. 
Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.

WARNING

1.  To reduce the risk of burns, fire, electric shock or injury to persons:
2.  Unplug this furnishing from the electrical outlet before cleaning.
3.  Unplug from outlet before adding or removing parts.
4.  Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has 

been dropped or damaged, or dropped into water. Contact Oakworks Customer Service before use at 

717.235.6807.

5.  Keep the cord away from heated surfaces.
6.  Never drop or insert any object into any opening.
7.  Do not use outdoors.

8.  Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

DANGER

Risk of electric shock - Connect this furnishing to a properly grounded outlet only. See Grounding Instructions in 

this manual.
Electrical Shock Hazard - The power supply/control module is located on the lift frame. No user serviceable 

parts are inside. Refer servicing to qualified personnel. Unplug wall plug prior to contact with any cables con-

nected to the power supply. 

2

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for Clodagh Leo





















Reviews: