background image

Mineral Mizer Owner’s Manual (rev. 7) 

DWS-SADI  

 

Question or comments? Contact O-SO Pure at (800) OSO-PURE or 

[email protected]

Copyright

©

 2016 O-SO Pure. All rights reserved. 

Page 7 of 16 

7. 

Drain Saddle

 – The Drain Saddle installs on a standard 1½” O.D. vertical section of drain pipe. 

Install it above the trap and away from the garbage disposal outlet, if any. Position it to allow 
adequate space for drilling through the pipe, angling the fitting in the direction of the Mineral 
Mizer installation. Tighten the Drain Saddle evenly and firmly so a good seal is made. Avoid over 
tightening. Drill a 5/16” hole in the drain pipe through the drain fitting opening while supporting 
the drain against drilling pressure.

 

Connect the Mineral Mizer to plumbing 

8.

 

Filter Sumps

 - Remove the plastic shrink wrap from all filters. Place the filter with the yellow dot 

in the left Filter Sump and install it on the filter cap marked with a yellow dot on the bracket. 
Place the filters with the red dots in the center and right Filter Sumps, again marked by 
corresponding dots on the bracket. Hand-tighten all the Filter Sumps so they are snug. Do not use 
the provided filter wrench to tighten the filter Sumps unless absolutely necessary. Place the 
Mineral Mizer in its service location. 

 

9.

 

Drain Tube (black)

 - After cutting to the appropriate length, 

connect the Drain Tube between the Mineral Mizer’s check 
valve marked 

To Drain

 and the Drain Saddle fitting. 

 

10.

 

Feed Water Tube (red)

 – 

After cutting to the 
appropriate length, insert the 
elbow end of the Feed Water 
Tube into the fitting marked 

To Feed Water

 and the other 

end into the Angle Stop Valve 
fitting previously installed on 
the sink plumbing. 

 

11.

 

Tank Tube (blue)

 – Connect the Tank Tube to the 3/8” elbow on 

the Storage Tank Connector at back left, while the other end 
hooks up to the elbow ball valve on the storage tank. Keep tank 
valve 

CLOSED 

for the moment.

 

 

12.

 

D.I. Dispensing Connector (blue)

 

 

*

FOR DWS-SADI 

(DISPENSING CONNECTOR TO RED FAUCET):

 

Insert one end 

of 3/8” BLUE Tube length into D.I. Dispensing Connector and the other 
end into the bottom of the Red Faucet. Install the Red Faucet per its 
included instructions. Location options include the sink pop-out or 
through the countertop overhanging the sink. 
 
 

 

Tank Tube 

 

Drain Tube 

 

Feed Water Tube 

Summary of Contents for DWS-SADI

















Reviews: