background image

The exhaust outlet of the silencer can be rotated to 
any desired position in the following manner:

Loosen the locknut and assembly screw.
Set the exhaust outlet at the required position by 
rotating the rear part of the silencer.
Re-tighten the assembly screw, followed by the 
locknut. 

SILENCER

1)
2)

3)   

NOTE : 

The standard expansion-chamber type silencer is 
quite effective, but reduces power to some degree.

Assembly screw

Cone baffle

Turn to requlred position

Exhaust outlet

Locknut

Exhaust pressure nipple

Before connecting the throttle-lever / servo linkage, 
make sure that no part of the linkage interferes with 
the internal structure of the aircraft or wiring, etc., 
when the throttle is fully open or fully closed.

Set the throttle lever linkage so that the throttle ro-
tor is (a) fully open when the transmitter throttle 
stick is fully advanced and  (b) fully closed when 
the throttle stick is fully retarded.
Adjustment of the throttle rotor opening at the idling 
position can then be made with the throttle trim lev-
er on the transmitter.
(Select throttle-lever and servo-horn hole positions 
that will avoid excessive pushrod travel causing the 
throttle to bind at either end.)

THROTTLE LINKAGE

When adjusting the throttle lever angle, relative to 
the rotor,hold the rotor at about half-way between 
the open and closed positions while loosening 
and tightening the fixing screw, otherwise the 
rotor, rotor guide screw,throttle stop screw or 
carburettor body may become burred and 
damaged.

Note: 

E-4010 Silencer

11

Summary of Contents for MAX-40FX












































Reviews: