background image

4

!  

NOTES

Before starting the engine, always check 
the  tightness  of  all  the  screws  and  nuts 
especially  those  of  joint  and  movable 
parts  such  as  throttle  arm.  Missing 
retightening  the  loose  screws  and  nuts 
often  causes  the  parts  breakage  that  is 
capable of harming you. 

This  engine  is  intended  for  model  cars. 
Do  not  attempt  to  use  it  for  any  other 
purpose.

Mount  the  engine  in  your  model 
securely,  following  the  manufacturer's 
recommendations,  using  appropriate 
screws and locknuts.

Install  an  effective  silencer  (muffler). 
Frequent  close  exposure  to  a  noisy 
exhaust  (especially  in  the  case  of  the 
more  powerful  highspeed  engines)  may 
eventually impair your hearing and such 
noise  is  also  likely  to  cause  annoyance 
to others over a wide area.

The  wearing  of  safety  glasses  is  also 
strongly recommended.

Take  care  that  the  glowplug  clip  or 
battery  leads  do  not  come  into  contact 
with  rotating  parts.  Also  check  that  the 
linkage to the throttle arm is secure.

For  their  safety,  keep  all  onlookers 
(especially  small  children)  well  back  (at 
least  20  feet  or  6  meters)  when 
preparing your model for running.

5

!  

NOTES

To  stop  the  engine,  fully  retard  the 
throttle stick and trim lever on the trans-
mitter,  or,  in  an  emergency,  cut  off  the 
fuel  supply  by  pinching  the  fuel  delivery 
line from the tank.

Warning! Immediately after  a  glowplug-
ignition engine has been run and is still 
warm,  conditions  sometimes  exist 
whereby it is just possible for the engine to 
abruptly  restart  if  it  is  rotated  over 
compression  WITHOUT  the  glowplug 
battery being reconnected.

Pull  the  operating  handle  straight  out 
when starting the engine, so that the cord 
does not rub against the vehicle body or 
engine. This will help prevent the cord 
from  being  damaged  by  abrasion  or 
engine heat.

Do not extend the starter cord more than 
40cm  (16").  Do  not  abruptly  release  the 
operating  handle.  Allow  the  cord  to 
rewind  smoothly  while  still  holding  the 
handle. 

Do not attempt to disassemble the recoil 
starter of the 12TG-X and 12TG-PX. 
If you do so, the very strong spring inside 
will  be  suddenly  ejected.  This  can  be 
very dangerous.

Summary of Contents for MAX-12TG-P






























Reviews: